I created these macros because none of Klipper's fan control options (like [temperature_fan]) did quite what I wanted.
These macros are automatically invoked when your target bed temp is changed (and ONLY then). Because of this, you do not need to add anything to your other macros.
They have a pretty simple behavior. All they do is:
- Automatically set the bed fans to
variable_slowspeed while the bed is heating up. - Automatically set the bed fans to
variable_fastspeed once target bed temp is reached. - Automatically turn off the bed fans when the bed is turned off.
These macros do NOT read the chamber temperature. If your chamber is getting too hot, simply lower the fan speeds.
If the above is not the behavior you desire, you have some other options:
- Configure your bed fans as
[fan_generic]and control them manually withSET_FAN_SPEEDin yourPRINT_START/PRINT_ENDetc. - Use one of Klipper's other fan control methods like
[temperature_fan]. - Modify these macros to achieve your desired custom behavior (or write new ones).
Please see the "Information" section first.
1) Place the .cfg file (located in the Klipper_Macros folder) in the same directory as your printer.cfg file.
2) Add [include bedfans.cfg] to your printer.cfg.
3) Change pin for your fans in the second section.
- This is intentionally left blank so that it will error if you don't fill it in.
4) Configure the options in the first section:
variable_thresholdsets the bed temp threshold at which your bed fans will be used.- Default is 100C (so it does not enable for PLA)
variable_slowsets the fan speed for when the bed is heating.variable_fastsets the fan speed for when the bed is at temperature.
bedfans-dualcontrol.cfgoptionally allows for setting inner and outer fan speeds separately, for a quad fan configuration.- If you get "Heater heater_bed not heating at expected rate" errors, then you have one or both of your fan speeds set too high.
variable_slowcan be set to 0 if you prefer the fans to remain off during heatup.
Bill of materials (per fan):
- 1x 5015 fan
- 1x M3x25
- 1x M3x20
- 1x M3 heat set insert
- 1x M3x8 or M3x10 (optional, I only mount with one screw)
- My chamber now reaches about 60-66C with a quad fan configuration, whereas it only reached roughly 48-50C previously. Chamber temp is also reached more quickly.
-
Technically your bed heater is not being run at full power with the default configs, however I do not recommend pushing it. Since you can't control max power at runtime, your bed will run at too high of a power while heating, risking warping your bed.
-
I also do not recommend tinkering with your verify_heater (thermal runaway protection) settings.
- Recommended max_power is 0.4 watts per cm2:
For example, for a 300 mm^2 bed:
30 cm * 30 cm = 900 cm^2.
900 cm^2 * 0.4 Watts = 360 Watts max.
If you have a 750 watt heater, that's 48% power, or 0.48 max_power.
- I did not find it necessary. Bed heaters do not seem to be terribly sensitive to this.
- Yes, this is normal. It should recover within 60 seconds. If not, then your fan speeds are too high.
- I just used generic multi-pack fans. There is no need for anything fancy here.
- Triple/quad fans is more for even airflow than raw airflow. In fact you will likely not be able to run them at 100% without outrunning your bed heater. I personally prefer triple/quad fans to avoid any possibility of "tacoing" my bed due to uneven temperatures. Triple fans is probably the "sweet spot".
- Almost certainly not. I originally set it up that way because it was easier to wire in my particular case, so I took advantage of it. Triple fans with "single" control is probably the best balance of cost, complexity, and performance.
- No. Stop it. Bad.
(looks a bit tight since CAD is for a 250mm)
