Unable to run openHASP on Sunton ESP32-8048S070C #738

mak-42 · 2024-05-21T20:14:09Z

mak-42
May 21, 2024

I flashed "v0.7.0-rc12" from "https://nightly.openhasp.com" and it can not run. "OPENHASP" displayed during a part of asecond on the screen and the device reboots again infinitely.
The logs shows some problem on "TFT : Starting" step.
The device itself seems to work well (I flashed lvgl demo downloaded from manufactory's site, it works).

Could you, please, prompt me, what I do wrong?

Logs:

ESP-ROM:esp32s3-20210327
Build:Mar 27 2021
rst:0x1 (POWERON),boot:0x28 (SPI_FAST_FLASH_BOOT)
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fce3808,len:0x128
load:0x403c9700,len:0xb90
load:0x403cc700,len:0x28cc
entry 0x403c98b8



        open____ _____ _____ _____
          |  |  |  _  |   __|  _  |
          |     |     |__   |   __|
          |__|__|__|__|_____|__|
        Home Automation Switch Plate
        Open Hardware edition v0.7.0-rc12

[       0.082][212980/248800 14][    0/    0  0] DBUG: Started @ 115200 bps
#[       0.091][212980/248800 14][    0/    0  0] DBUG: Environment: sunton-8048s070c_16MB
#[       0.101][212980/248800 14][    0/    0  0] UART: Started
#[       0.108][212980/248800 14][    0/    0  0] UART: Client login from serial
#[       0.119][212980/248800 14][    0/    0  0] CONF: Failed to load /config.json
Prompt > [       0.129][212980/248800 14][    0/    0  0] CONF: Loading EEPROM
Prompt > [       0.138][212980/248800 14][    0/    0  0] CONF: Loaded EEPROM
Prompt > [       0.147][212980/248864 14][    0/    0  0] DBUG: Loading debug settings
Prompt > [       0.157][212980/248864 14][    0/    0  0] GPIO: Loading GUI settings
Prompt > [       0.166][212980/248864 14][    0/    0  0] HASP: Loading HASP settings
Prompt > [       0.176][212980/248864 14][    0/    0  0] WIFI: Loading WiFi settings
Prompt > [       0.202][212980/246940 13][    0/    0  0] MQTT: Loading MQTT settings
Prompt > [       0.212][212980/246940 13][    0/    0  0] TELN: Loading Telnet settings
Prompt > [       0.222][212980/246940 13][    0/    0  0] MDNS: Loading MDNS settings
Prompt > [       0.231][212980/246940 13][    0/    0  0] HTTP: Loading HTTP settings
Prompt > [       0.241][212980/246940 13][    0/    0  0] GPIO: Loading GPIO settings
Prompt > [       0.251][212980/246940 13][    0/    0  0] CONF: Settings loaded
Prompt > [       0.298][204788/215980  5][    0/    0  0] MSGR: Starting...
Prompt > [       0.307][204788/216176  5][    0/    0  0] MSGR: Started
Prompt > [       0.316][204788/216176  5][    0/    0  0] TFT : Starting...
Prompt > [       0.324][204788/216152  5][    0/    0  0] TFT : Starting...
Terminal disconnected: NetworkError: The device has been lost.

Answered by TLaren

May 27, 2024

OK, I was doing the old reset and see what changes. I touched the screen and it stopped blinking.
Is that a hint?
Then I touched again, it said to setup WiFi.
I enter my info and click the check and the logs show this.
...
[ 95.664][81908/93948 12][54588/55892 3] WIFI: Connecting to instanet... 1
Prompt > [ 95.924][81908/94140 12][54588/55892 3] WIFI: Connecting to instanet... 2
Prompt > [ 96.184][81908/94140 12][54588/55892 3] WIFI: Connecting to instanet... 3
Prompt > [ 96.444][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 4
Prompt > [ 96.704][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 5
Prompt > [ 96.964][81908/94144 12][54588/55892 3] WIFI: Connect…

View full answer

TLaren · 2024-05-27T08:32:44Z

TLaren
May 27, 2024

Just about the same place, 1 line further.
EXP32-8048D070C
The module seems good, I have several and have programmed them up for other projects using LGFX.

...
ESP-ROM:esp32s3-20210327
Build:Mar 27 2021
rst:0x1 (POWERON),boot:0x2a (SPI_FAST_FLASH_BOOT)
SPIWP:0xee
mode:DIO, clock div:1
load:0x3fce3808,len:0x128
load:0x403c9700,len:0xb90
load:0x403cc700,len:0x28cc
entry 0x403c98b8

    open____ _____ _____ _____
      |  |  |  _  |   __|  _  |
      |     |     |__   |   __|
      |__|__|__|__|_____|__|
    Home Automation Switch Plate
    Open Hardware edition v0.7.0-rc12

[ 0.082][212980/248800 14][ 0/ #[ 0.091][212980/248800 14][ 0/ #[ 0.101][212980/248800 14][ 0/ #[ 0.108][212980/248800 14][ 0/ #[ 0.119][212980/248800 14][ 0/ Prompt > [ 0.129][212980/248800 14][ Prompt > [ 0.138][212980/248800 14][ Prompt > [ 0.147][212980/248864 14][ Prompt > [ 0.156][212980/248864 14][ Prompt > [ 0.166][212980/248864 14][ Prompt > [ 0.176][212980/248864 14][ Prompt > [ 0.201][212980/247028 13][ Prompt > [ 0.211][212980/247028 13][ Prompt > [ 0.221][212980/247028 13][ Prompt > [ 0.231][212980/247028 13][ Prompt > [ 0.240][212980/247028 13][ Prompt > [ 0.250][212980/247028 13][ Prompt > [ 0.297][204788/216072 5][ Prompt > [ 0.306][204788/216268 5][ Prompt > [ 0.314][204788/216268 5][ Prompt > [ 0.323][204788/216244 5][ Prompt > [ 0.354][204788/213312 3][ Terminal disconnected: NetworkError: ...
Any help or suggestions would be appreciated 0 0] DBUG: Started @ 115200 bps
0 0] DBUG: Environment: sunton-8048s070c_16MB
0 0] UART: Started
0 0] UART: Client login from serial
0 0] CONF: Failed to load /config.json
0/ 0 0] CONF: Loading EEPROM
0/ 0 0] CONF: Loaded EEPROM
0/ 0 0] DBUG: Loading debug settings
0/ 0 0] GPIO: Loading GUI settings
0/ 0 0] HASP: Loading HASP settings
0/ 0 0] WIFI: Loading WiFi settings
0/ 0 0] MQTT: Loading MQTT settings
0/ 0 0] TELN: Loading Telnet settings
0/ 0 0] MDNS: Loading MDNS settings
0/ 0 0] HTTP: Loading HTTP settings
0/ 0 0] GPIO: Loading GPIO settings
0/ 0 0] CONF: Settings loaded
0/ 0 0] MSGR: Starting...
0/ 0 0] MSGR: Started
0/ 0 0] TFT : Starting...
0/ 0 0] TFT : Starting...
0/ 0 0] TFT : Started
The device has been lost.

0 replies

TLaren · 2024-05-27T08:49:00Z

TLaren
May 27, 2024

OK, I was doing the old reset and see what changes. I touched the screen and it stopped blinking.
Is that a hint?
Then I touched again, it said to setup WiFi.
I enter my info and click the check and the logs show this.
...
[ 95.664][81908/93948 12][54588/55892 3] WIFI: Connecting to instanet... 1
Prompt > [ 95.924][81908/94140 12][54588/55892 3] WIFI: Connecting to instanet... 2
Prompt > [ 96.184][81908/94140 12][54588/55892 3] WIFI: Connecting to instanet... 3
Prompt > [ 96.444][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 4
Prompt > [ 96.704][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 5
Prompt > [ 96.964][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 6
Prompt > [ 97.224][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 7
Prompt > [ 97.484][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 8
Prompt > [ 97.744][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 9
Prompt > [ 98.004][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 10
Prompt > [ 98.264][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 11
Prompt > [ 98.524][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 12
Prompt > [ 98.784][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 13
Prompt > [ 99.044][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 14
Prompt > [ 99.304][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 15
Prompt > [ 99.564][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 16
Prompt > [ 99.824][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 17
Prompt > [ 100.084][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 18
Prompt > [ 100.344][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 19
Prompt > [ 100.604][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 20
Prompt > [ 100.864][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 21
Prompt > [ 101.124][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 22
Prompt > [ 101.384][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 23
Prompt > [ 101.644][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 24
Prompt > [ 101.904][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 25
Prompt > [ 102.164][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 26
Prompt > [ 102.424][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 27
Prompt > [ 102.684][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 28
Prompt > [ 102.944][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 29
Prompt > [ 103.204][81908/94144 12][54588/55892 3] WIFI: Connecting to instanet... 30
Prompt > [ 103.464][81908/94096 12][54588/55892 3] WIFI: Received IP address 0.0.0.0
Prompt > [ 103.474][81908/94096 12][54588/55892 3] WIFI: Received IP address 0.0.0.0
Prompt > [ 156.596][81908/94420 13][55392/55900 1] MSGR: File not found: L:/idle_short.cmd
...
The screen still show the 'enter wifi Ssid and password stuff.
I then realize I have the Ssid wrong. Correct ir and I am "plate".
So I'm not sure about the flashing until I touch the screen but it seems to be up.
Just have to figure the next steps.

2 replies

mak-42 May 27, 2024
Author

Thanks a lot for the hint. I touched a screen, and it stopped blinking as well and I was able to setup WIFI.

TLaren May 28, 2024

So what is next.
Mine doesn't show up in HA that I can tell. Somewhere I read that it would appear in the Overview.
In Devices I see openhasp but it shows Not loaded.
I read another post about a missing yaml file but I'm still looking where to put it and what to put in it.
I did create a pages.json (actually edited it) using the web interface. Added a button, well a square for now.
using the web interface I also looked at the config.json file
...
{
"wifi": {
"ssid": "Instanet",
"pass": ""
},
"mqtt": {
"host": "192.168.15.11",
"user": "mqttu",
"pass": "",
"topic": {
"node": "hasp/%hostname%/%topic%",
"group": "hasp/plates/%topic%",
"broadcast": "hasp/broadcast/%topic%",
"hass": "homeassistant/status"
},
"port": 1883,
"name": "plate"
},
"telnet": {
"enable": 1,
"port": 23
},
"mdns": {
"enable": 1
},
"http": {
"enable": true,
"port": 80,
"user": "",
"pass": "********"
},
"gpio": {
"config": [
0,
0,
0,
0,
0,
0,
0,
0
]
},
"debug": {
"ansi": 0,
"baud": 115200,
"tele": 300,
"host": "",
"port": 514,
"proto": 0,
"log": 0
},
"gui": {
"idle1": 60,
"idle2": 120,
"bckl": 2,
"bcklinv": 0,
"rotate": 0,
"cursor": 0,
"invert": 0,
"calibration": [
0,
65535,
0,
65535,
0,
0,
0,
0
]
},
"hasp": {
"startpage": 1,
"startdim": 255,
"theme": 2,
"color1": "#00b6ff",
"color2": "#ff9962",
"font": "",
"pages": "/pages.jsonl"
}
}
...
What to do next, read more I guess.

StreakingJerry · 2024-06-19T16:46:18Z

StreakingJerry
Jun 19, 2024

I have opened an bug issue for this.
https://github.com/HASwitchPlate/openHASP/issues/754

0 replies

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Unable to run openHASP on Sunton ESP32-8048S070C #738

{{title}}

Replies: 3 comments 2 replies

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

Select a reply

Unable to run openHASP on Sunton ESP32-8048S070C #738

mak-42 May 21, 2024

Replies: 3 comments · 2 replies

TLaren May 27, 2024

TLaren May 27, 2024

mak-42 May 27, 2024 Author

TLaren May 28, 2024

StreakingJerry Jun 19, 2024

mak-42
May 21, 2024

Replies: 3 comments 2 replies

TLaren
May 27, 2024

TLaren
May 27, 2024

mak-42 May 27, 2024
Author

StreakingJerry
Jun 19, 2024