stm32f2xx_gpio.c

/**
  ******************************************************************************
  * @file    stm32f2xx_gpio.c
  * @author  MCD Application Team
  * @version V1.1.2
  * @date    05-March-2012 
  * @brief   This file provides firmware functions to manage the following 
  *          functionalities of the GPIO peripheral:           
  *           - Initialization and Configuration
  *           - GPIO Read and Write
  *           - GPIO Alternate functions configuration
  * 
  *  @verbatim
  *
  *          ===================================================================
  *                                 How to use this driver
  *          ===================================================================       
  *           1. Enable the GPIO AHB clock using the following function
  *                RCC_AHB1PeriphClockCmd(RCC_AHB1Periph_GPIOx, ENABLE);
  *             
  *           2. Configure the GPIO pin(s) using GPIO_Init()
  *              Four possible configuration are available for each pin:
  *                - Input: Floating, Pull-up, Pull-down.
  *                - Output: Push-Pull (Pull-up, Pull-down or no Pull)
  *                          Open Drain (Pull-up, Pull-down or no Pull).
  *                  In output mode, the speed is configurable: 2 MHz, 25 MHz,
  *                  50 MHz or 100 MHz.
  *                - Alternate Function: Push-Pull (Pull-up, Pull-down or no Pull)
  *                                      Open Drain (Pull-up, Pull-down or no Pull).
  *                - Analog: required mode when a pin is to be used as ADC channel
  *                          or DAC output.
  * 
  *          3- Peripherals alternate function:
  *              - For ADC and DAC, configure the desired pin in analog mode using 
  *                  GPIO_InitStruct->GPIO_Mode = GPIO_Mode_AN;
  *              - For other peripherals (TIM, USART...):
  *                 - Connect the pin to the desired peripherals' Alternate 
  *                   Function (AF) using GPIO_PinAFConfig() function
  *                 - Configure the desired pin in alternate function mode using
  *                   GPIO_InitStruct->GPIO_Mode = GPIO_Mode_AF
  *                 - Select the type, pull-up/pull-down and output speed via 
  *                   GPIO_PuPd, GPIO_OType and GPIO_Speed members
  *                 - Call GPIO_Init() function
  *        
  *          4. To get the level of a pin configured in input mode use GPIO_ReadInputDataBit()
  *          
  *          5. To set/reset the level of a pin configured in output mode use
  *             GPIO_SetBits()/GPIO_ResetBits()
  *               
  *          6. During and just after reset, the alternate functions are not 
  *             active and the GPIO pins are configured in input floating mode
  *             (except JTAG pins).
  *
  *          7. The LSE oscillator pins OSC32_IN and OSC32_OUT can be used as 
  *             general-purpose (PC14 and PC15, respectively) when the LSE
  *             oscillator is off. The LSE has priority over the GPIO function.
  *
  *          8. The HSE oscillator pins OSC_IN/OSC_OUT can be used as 
  *             general-purpose PH0 and PH1, respectively, when the HSE 
  *             oscillator is off. The HSE has priority over the GPIO function.
  *             
  *  @endverbatim        
  *
  ******************************************************************************
  * @attention
  *
  * <h2><center>&copy; COPYRIGHT 2012 STMicroelectronics</center></h2>
  *
  * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
  * You may not use this file except in compliance with the License.
  * You may obtain a copy of the License at:
  *
  *        http://www.st.com/software_license_agreement_liberty_v2
  *
  * Unless required by applicable law or agreed to in writing, software 
  * distributed under the License is distributed on an "AS IS" BASIS, 
  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
  * See the License for the specific language governing permissions and
  * limitations under the License.
  *
  ******************************************************************************
  */

/* Includes ------------------------------------------------------------------*/
#include "stm32f2xx_gpio.h"
#include "stm32f2xx_rcc.h"

/** @addtogroup STM32F2xx_StdPeriph_Driver
  * @{
  */

/** @defgroup GPIO 
  * @brief GPIO driver modules
  * @{
  */ 

/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/

/** @defgroup GPIO_Private_Functions
  * @{
  */ 

/** @defgroup GPIO_Group1 Initialization and Configuration
 *  @brief   Initialization and Configuration
 *
@verbatim   
 ===============================================================================
                        Initialization and Configuration
 ===============================================================================  

@endverbatim
  * @{
  */

/**
  * @brief  Deinitializes the GPIOx peripheral registers to their default reset values.
  * @note   By default, The GPIO pins are configured in input floating mode (except JTAG pins).
  * @param  GPIOx: where x can be (A..I) to select the GPIO peripheral.
  * @retval None
  */
#ifndef BOOT
void GPIO_DeInit(GPIO_TypeDef* GPIOx)
{
  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));

  if (GPIOx == GPIOA)
  {
    RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOA, ENABLE);
    RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOA, DISABLE);
  }
  else if (GPIOx == GPIOB)
  {
    RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOB, ENABLE);
    RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOB, DISABLE);
  }
  else if (GPIOx == GPIOC)
  {
    RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOC, ENABLE);
    RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOC, DISABLE);
  }
  else if (GPIOx == GPIOD)
  {
    RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOD, ENABLE);
    RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOD, DISABLE);
  }
  else if (GPIOx == GPIOE)
  {
    RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOE, ENABLE);
    RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOE, DISABLE);
  }
  else if (GPIOx == GPIOF)
  {
    RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOF, ENABLE);
    RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOF, DISABLE);
  }
  else if (GPIOx == GPIOG)
  {
    RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOG, ENABLE);
    RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOG, DISABLE);
  }
  else if (GPIOx == GPIOH)
  {
    RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOH, ENABLE);
    RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOH, DISABLE);
  }
  else
  {
    if (GPIOx == GPIOI)
    {
      RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOI, ENABLE);
      RCC_AHB1PeriphResetCmd(RCC_AHB1Periph_GPIOI, DISABLE);
    }
  }
}
#endif

/**
  * @brief  Initializes the GPIOx peripheral according to the specified parameters in the GPIO_InitStruct.
  * @param  GPIOx: where x can be (A..I) to select the GPIO peripheral.
  * @param  GPIO_InitStruct: pointer to a GPIO_InitTypeDef structure that contains
  *         the configuration information for the specified GPIO peripheral.
  * @retval None
  */
void GPIO_Init(GPIO_TypeDef* GPIOx, GPIO_InitTypeDef* GPIO_InitStruct)
{
  uint32_t pinpos = 0x00, pos = 0x00 , currentpin = 0x00;

  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
  assert_param(IS_GPIO_PIN(GPIO_InitStruct->GPIO_Pin));
  assert_param(IS_GPIO_MODE(GPIO_InitStruct->GPIO_Mode));
  assert_param(IS_GPIO_PUPD(GPIO_InitStruct->GPIO_PuPd));

  /* -------------------------Configure the port pins---------------- */
  /*-- GPIO Mode Configuration --*/
  for (pinpos = 0x00; pinpos < 0x10; pinpos++)
  {
    pos = ((uint32_t)0x01) << pinpos;
    /* Get the port pins position */
    currentpin = (GPIO_InitStruct->GPIO_Pin) & pos;

    if (currentpin == pos)
    {
      GPIOx->MODER  &= ~(GPIO_MODER_MODER0 << (pinpos * 2));
      GPIOx->MODER |= (((uint32_t)GPIO_InitStruct->GPIO_Mode) << (pinpos * 2));

      if ((GPIO_InitStruct->GPIO_Mode == GPIO_Mode_OUT) || (GPIO_InitStruct->GPIO_Mode == GPIO_Mode_AF))
      {
        /* Check Speed mode parameters */
        assert_param(IS_GPIO_SPEED(GPIO_InitStruct->GPIO_Speed));

        /* Speed mode configuration */
        GPIOx->OSPEEDR &= ~(GPIO_OSPEEDER_OSPEEDR0 << (pinpos * 2));
        GPIOx->OSPEEDR |= ((uint32_t)(GPIO_InitStruct->GPIO_Speed) << (pinpos * 2));

        /* Check Output mode parameters */
        assert_param(IS_GPIO_OTYPE(GPIO_InitStruct->GPIO_OType));

        /* Output mode configuration*/
        GPIOx->OTYPER  &= ~((GPIO_OTYPER_OT_0) << ((uint16_t)pinpos)) ;
        GPIOx->OTYPER |= (uint16_t)(((uint16_t)GPIO_InitStruct->GPIO_OType) << ((uint16_t)pinpos));
      }

      /* Pull-up Pull down resistor configuration*/
      GPIOx->PUPDR &= ~(GPIO_PUPDR_PUPDR0 << ((uint16_t)pinpos * 2));
      GPIOx->PUPDR |= (((uint32_t)GPIO_InitStruct->GPIO_PuPd) << (pinpos * 2));
    }
  }
}

/**
  * @brief  Fills each GPIO_InitStruct member with its default value.
  * @param  GPIO_InitStruct : pointer to a GPIO_InitTypeDef structure which will be initialized.
  * @retval None
  */
#ifndef BOOT
void GPIO_StructInit(GPIO_InitTypeDef* GPIO_InitStruct)
{
  /* Reset GPIO init structure parameters values */
  GPIO_InitStruct->GPIO_Pin  = GPIO_Pin_All;
  GPIO_InitStruct->GPIO_Mode = GPIO_Mode_IN;
  GPIO_InitStruct->GPIO_Speed = GPIO_Speed_2MHz;
  GPIO_InitStruct->GPIO_OType = GPIO_OType_PP;
  GPIO_InitStruct->GPIO_PuPd = GPIO_PuPd_NOPULL;
}
#endif

/**
  * @brief  Locks GPIO Pins configuration registers.
  * @note   The locked registers are GPIOx_MODER, GPIOx_OTYPER, GPIOx_OSPEEDR,
  *         GPIOx_PUPDR, GPIOx_AFRL and GPIOx_AFRH.
  * @note   The configuration of the locked GPIO pins can no longer be modified
  *         until the next reset.
  * @param  GPIOx: where x can be (A..I) to select the GPIO peripheral.
  * @param  GPIO_Pin: specifies the port bit to be locked.
  *          This parameter can be any combination of GPIO_Pin_x where x can be (0..15).
  * @retval None
  */
#ifndef BOOT
void GPIO_PinLockConfig(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
{
  __IO uint32_t tmp = 0x00010000;

  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
  assert_param(IS_GPIO_PIN(GPIO_Pin));

  tmp |= GPIO_Pin;
  /* Set LCKK bit */
  GPIOx->LCKR = tmp;
  /* Reset LCKK bit */
  GPIOx->LCKR =  GPIO_Pin;
  /* Set LCKK bit */
  GPIOx->LCKR = tmp;
  /* Read LCKK bit*/
  tmp = GPIOx->LCKR;
  /* Read LCKK bit*/
  tmp = GPIOx->LCKR;
}
#endif

/**
  * @}
  */

/** @defgroup GPIO_Group2 GPIO Read and Write
 *  @brief   GPIO Read and Write
 *
@verbatim   
 ===============================================================================
                              GPIO Read and Write
 ===============================================================================  

@endverbatim
  * @{
  */

/**
  * @brief  Reads the specified input port pin.
  * @param  GPIOx: where x can be (A..I) to select the GPIO peripheral.
  * @param  GPIO_Pin: specifies the port bit to read.
  *         This parameter can be GPIO_Pin_x where x can be (0..15).
  * @retval The input port pin value.
  */
#ifndef BOOT
uint8_t GPIO_ReadInputDataBit(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
{
  uint8_t bitstatus = 0x00;

  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
  assert_param(IS_GET_GPIO_PIN(GPIO_Pin));

  if ((GPIOx->IDR & GPIO_Pin) != (uint32_t)Bit_RESET)
  {
    bitstatus = (uint8_t)Bit_SET;
  }
  else
  {
    bitstatus = (uint8_t)Bit_RESET;
  }
  return bitstatus;
}
#endif

/**
  * @brief  Reads the specified GPIO input data port.
  * @param  GPIOx: where x can be (A..I) to select the GPIO peripheral.
  * @retval GPIO input data port value.
  */
#ifndef BOOT
uint16_t GPIO_ReadInputData(GPIO_TypeDef* GPIOx)
{
  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));

  return ((uint16_t)GPIOx->IDR);
}
#endif
/**
  * @brief  Reads the specified output data port bit.
  * @param  GPIOx: where x can be (A..I) to select the GPIO peripheral.
  * @param  GPIO_Pin: specifies the port bit to read.
  *          This parameter can be GPIO_Pin_x where x can be (0..15).
  * @retval The output port pin value.
  */
#ifndef BOOT
uint8_t GPIO_ReadOutputDataBit(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
{
  uint8_t bitstatus = 0x00;

  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
  assert_param(IS_GET_GPIO_PIN(GPIO_Pin));

  if ((GPIOx->ODR & GPIO_Pin) != (uint32_t)Bit_RESET)
  {
    bitstatus = (uint8_t)Bit_SET;
  }
  else
  {
    bitstatus = (uint8_t)Bit_RESET;
  }
  return bitstatus;
}
#endif

/**
  * @brief  Reads the specified GPIO output data port.
  * @param  GPIOx: where x can be (A..I) to select the GPIO peripheral.
  * @retval GPIO output data port value.
  */
#ifndef BOOT
uint16_t GPIO_ReadOutputData(GPIO_TypeDef* GPIOx)
{
  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));

  return ((uint16_t)GPIOx->ODR);
}
#endif
/**
  * @brief  Sets the selected data port bits.
  * @note   This functions uses GPIOx_BSRR register to allow atomic read/modify 
  *         accesses. In this way, there is no risk of an IRQ occurring between
  *         the read and the modify access.
  * @param  GPIOx: where x can be (A..I) to select the GPIO peripheral.
  * @param  GPIO_Pin: specifies the port bits to be written.
  *          This parameter can be any combination of GPIO_Pin_x where x can be (0..15).
  * @retval None
  */
#ifndef BOOT
void GPIO_SetBits(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
{
  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
  assert_param(IS_GPIO_PIN(GPIO_Pin));

  GPIOx->BSRRL = GPIO_Pin;
}
#endif
/**
  * @brief  Clears the selected data port bits.
  * @note   This functions uses GPIOx_BSRR register to allow atomic read/modify 
  *         accesses. In this way, there is no risk of an IRQ occurring between
  *         the read and the modify access.
  * @param  GPIOx: where x can be (A..I) to select the GPIO peripheral.
  * @param  GPIO_Pin: specifies the port bits to be written.
  *          This parameter can be any combination of GPIO_Pin_x where x can be (0..15).
  * @retval None
  */
#ifndef BOOT
void GPIO_ResetBits(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
{
  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
  assert_param(IS_GPIO_PIN(GPIO_Pin));

  GPIOx->BSRRH = GPIO_Pin;
}
#endif

/**
  * @brief  Sets or clears the selected data port bit.
  * @param  GPIOx: where x can be (A..I) to select the GPIO peripheral.
  * @param  GPIO_Pin: specifies the port bit to be written.
  *          This parameter can be one of GPIO_Pin_x where x can be (0..15).
  * @param  BitVal: specifies the value to be written to the selected bit.
  *          This parameter can be one of the BitAction enum values:
  *            @arg Bit_RESET: to clear the port pin
  *            @arg Bit_SET: to set the port pin
  * @retval None
  */
#ifndef BOOT
void GPIO_WriteBit(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin, BitAction BitVal)
{
  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
  assert_param(IS_GET_GPIO_PIN(GPIO_Pin));
  assert_param(IS_GPIO_BIT_ACTION(BitVal));

  if (BitVal != Bit_RESET)
  {
    GPIOx->BSRRL = GPIO_Pin;
  }
  else
  {
    GPIOx->BSRRH = GPIO_Pin ;
  }
}
#endif

/**
  * @brief  Writes data to the specified GPIO data port.
  * @param  GPIOx: where x can be (A..I) to select the GPIO peripheral.
  * @param  PortVal: specifies the value to be written to the port output data register.
  * @retval None
  */
#ifndef BOOT
void GPIO_Write(GPIO_TypeDef* GPIOx, uint16_t PortVal)
{
  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));

  GPIOx->ODR = PortVal;
}
#endif
/**
  * @brief  Toggles the specified GPIO pins..
  * @param  GPIOx: where x can be (A..I) to select the GPIO peripheral.
  * @param  GPIO_Pin: Specifies the pins to be toggled.
  * @retval None
  */
#ifndef BOOT
void GPIO_ToggleBits(GPIO_TypeDef* GPIOx, uint16_t GPIO_Pin)
{
  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));

  GPIOx->ODR ^= GPIO_Pin;
}
#endif

/**
  * @}
  */

/** @defgroup GPIO_Group3 GPIO Alternate functions configuration function
 *  @brief   GPIO Alternate functions configuration function
 *
@verbatim   
 ===============================================================================
               GPIO Alternate functions configuration function
 ===============================================================================  

@endverbatim
  * @{
  */

/**
  * @brief  Changes the mapping of the specified pin.
  * @param  GPIOx: where x can be (A..I) to select the GPIO peripheral.
  * @param  GPIO_PinSource: specifies the pin for the Alternate function.
  *         This parameter can be GPIO_PinSourcex where x can be (0..15).
  * @param  GPIO_AFSelection: selects the pin to used as Alternate function.
  *          This parameter can be one of the following values:
  *            @arg GPIO_AF_RTC_50Hz: Connect RTC_50Hz pin to AF0 (default after reset) 
  *            @arg GPIO_AF_MCO: Connect MCO pin (MCO1 and MCO2) to AF0 (default after reset) 
  *            @arg GPIO_AF_TAMPER: Connect TAMPER pins (TAMPER_1 and TAMPER_2) to AF0 (default after reset) 
  *            @arg GPIO_AF_SWJ: Connect SWJ pins (SWD and JTAG)to AF0 (default after reset) 
  *            @arg GPIO_AF_TRACE: Connect TRACE pins to AF0 (default after reset)
  *            @arg GPIO_AF_TIM1: Connect TIM1 pins to AF1
  *            @arg GPIO_AF_TIM2: Connect TIM2 pins to AF1
  *            @arg GPIO_AF_TIM3: Connect TIM3 pins to AF2
  *            @arg GPIO_AF_TIM4: Connect TIM4 pins to AF2
  *            @arg GPIO_AF_TIM5: Connect TIM5 pins to AF2
  *            @arg GPIO_AF_TIM8: Connect TIM8 pins to AF3
  *            @arg GPIO_AF_TIM9: Connect TIM9 pins to AF3
  *            @arg GPIO_AF_TIM10: Connect TIM10 pins to AF3
  *            @arg GPIO_AF_TIM11: Connect TIM11 pins to AF3
  *            @arg GPIO_AF_I2C1: Connect I2C1 pins to AF4
  *            @arg GPIO_AF_I2C2: Connect I2C2 pins to AF4
  *            @arg GPIO_AF_I2C3: Connect I2C3 pins to AF4
  *            @arg GPIO_AF_SPI1: Connect SPI1 pins to AF5
  *            @arg GPIO_AF_SPI2: Connect SPI2/I2S2 pins to AF5
  *            @arg GPIO_AF_SPI3: Connect SPI3/I2S3 pins to AF6
  *            @arg GPIO_AF_USART1: Connect USART1 pins to AF7
  *            @arg GPIO_AF_USART2: Connect USART2 pins to AF7
  *            @arg GPIO_AF_USART3: Connect USART3 pins to AF7
  *            @arg GPIO_AF_UART4: Connect UART4 pins to AF8
  *            @arg GPIO_AF_UART5: Connect UART5 pins to AF8
  *            @arg GPIO_AF_USART6: Connect USART6 pins to AF8
  *            @arg GPIO_AF_CAN1: Connect CAN1 pins to AF9
  *            @arg GPIO_AF_CAN2: Connect CAN2 pins to AF9
  *            @arg GPIO_AF_TIM12: Connect TIM12 pins to AF9
  *            @arg GPIO_AF_TIM13: Connect TIM13 pins to AF9
  *            @arg GPIO_AF_TIM14: Connect TIM14 pins to AF9
  *            @arg GPIO_AF_OTG_FS: Connect OTG_FS pins to AF10
  *            @arg GPIO_AF_OTG_HS: Connect OTG_HS pins to AF10
  *            @arg GPIO_AF_ETH: Connect ETHERNET pins to AF11
  *            @arg GPIO_AF_FSMC: Connect FSMC pins to AF12
  *            @arg GPIO_AF_OTG_HS_FS: Connect OTG HS (configured in FS) pins to AF12
  *            @arg GPIO_AF_SDIO: Connect SDIO pins to AF12
  *            @arg GPIO_AF_DCMI: Connect DCMI pins to AF13
  *            @arg GPIO_AF_EVENTOUT: Connect EVENTOUT pins to AF15
  * @retval None
  */
void GPIO_PinAFConfig(GPIO_TypeDef* GPIOx, uint16_t GPIO_PinSource, uint8_t GPIO_AF)
{
  uint32_t temp = 0x00;
  uint32_t temp_2 = 0x00;
  
  /* Check the parameters */
  assert_param(IS_GPIO_ALL_PERIPH(GPIOx));
  assert_param(IS_GPIO_PIN_SOURCE(GPIO_PinSource));
  assert_param(IS_GPIO_AF(GPIO_AF));
  
  temp = ((uint32_t)(GPIO_AF) << ((uint32_t)((uint32_t)GPIO_PinSource & (uint32_t)0x07) * 4)) ;
  GPIOx->AFR[GPIO_PinSource >> 0x03] &= ~((uint32_t)0xF << ((uint32_t)((uint32_t)GPIO_PinSource & (uint32_t)0x07) * 4)) ;
  temp_2 = GPIOx->AFR[GPIO_PinSource >> 0x03] | temp;
  GPIOx->AFR[GPIO_PinSource >> 0x03] = temp_2;
}

/**
  * @}
  */ 

/**
  * @}
  */

/**
  * @}
  */ 

/**
  * @}
  */ 

/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/