Skip to content

Latest commit

 

History

History
146 lines (111 loc) · 5.39 KB

install_moode8_deb.md

File metadata and controls

146 lines (111 loc) · 5.39 KB
Raw

Install instructions for Moode 8

These instructions are for installing mpd_oled with a binary package on Moode 8 (valid for both 64-bit and legacy 32-bit kernel architecture).

The binary package should be the best option for most people, but if you would like to build and install the current mpd_oled repository code then see Install instructions for Moode 8 using source.

Base system

Install Moode. Ensure a command line prompt is available for entering the commands below (e.g. use SSH, enable in the Moode UI at Configure / System / Local Services / SSH term server, log in with default username 'pi', default password 'moodeaudio').

System settings

Configure your system to enable I2C or SPI, depending on how your OLED is connected.

I2C

I use a cheap 4 pin I2C SSH1106 display with a Raspberry Pi Zero. It is wired like this.

In /etc/modules I have the line i2c-dev

sudo nano /etc/modules

In /boot/config.txt I have the line dtparam=i2c_arm=on. The I2C bus speed on your system may be too slow for a reasonable screen refresh. Set a higher bus speed by adding the following line dtparam=i2c_arm_baudrate=400000 to /boot/config.txt, or try a higher value for a higher screen refresh (I use dtparam=i2c_arm_baudrate=800000 with a 25 FPS screen refresh)

sudo nano /boot/config.txt

Restart the Pi after making any system configuration changes.

SPI

I use a cheap 7 pin SPI SSH1106 display with a Raspberry Pi Zero. It is wired like this. In /boot/config.txt I have the line dtparam=spi=on.

sudo nano /boot/config.txt

Restart the Pi after making any system configuration changes.

Install the mpd_oled package

This will download and install the most recent mpd_oled binary package

wget -N http://pitastic.com/mpd_oled/packages/mpd_oled_moode_install_latest.sh
sudo bash mpd_oled_moode_install_latest.sh

Configure song status and time zone

In the Moode UI, set your timezone at Moode / Configure / System.

Enable the Moode metadata file, which includes information about the current song. The setting will either be at Moode / Configure / System / Local Services / Metadata file or Moode / Configure / Audio / MPD Options / Metadata file.

Configure a copy of the playing audio for the spectrum display

Go to Configure / Audio / ALSA Options, set ALSA Loopback to ON and click on SET.

Configure mpd_oled and set to run at boot

The mpd_oled program can be run with sudo mpd_oled_service_edit (plus options), and this also sets up mpd_oled with the same options as a service to be run at boot. Rerunning sudo mpd_oled_service_edit with different options will stop the current running mpd_oled and start it again with the new options. (Test commands can also be run with mpd_oled (plus options), and stopped with Ctrl-C, but ensure that no other copy of mpd_oled is running).

The OLED type MUST be specified with -o from the following list: 1 - Adafruit (SSD1306, SSD1309) SPI 128x64, 3 - Adafruit (SSD1306, SSD1309) I2C 128x64, 4 - Seeed I2C 128x64, 6 - SH1106 (SSH1106) I2C 128x64. 7 - SH1106 (SSH1106) SPI 128x64.

An example command, for a generic I2C SH1106 display (OLED type 6) with a display of 10 bars and a gap of 1 pixel between bars and a framerate of 20Hz is

sudo mpd_oled_service_edit -o 6 -b 10 -g 1 -f 20 -c alsa,plughw:Loopback,1

For I2C OLEDs (mpd_oled -o 3, 4 or 6) you may need to specify the I2C address, find this by running, e.g. sudo i2cdetect -y 1 and then specify the address with option -a, e.g. sudo mpd_oled_service_edit -o6 -a 3d .... If you have a reset pin connected, specify the GPIO number with option -r, e.g. sudo mpd_oled_service_edit -o6 -r 24 .... Specify the I2C bus number, if not 1, with option -B, e.g. sudo mpd_oled_service_edit -o6 -B 0 ...

For, SPI OLEDs (option -o 1 or 7), you may need to specify your reset pin GPIO number (option -r, default 25), DC pin GPIO number (option -D, default 24) or CS value (option -S, default 0).

If your display is upside down, you can rotate it 180 degrees with option '-R'.

Once the display is working, play some music and check the spectrum display is working and is synchronised with the music. If there are no bars then the audio copy may not have been configured correctly. If the bars seem jerky or not synchronized with the music then reduce the values of -b and/or -f.

If you run sudo mpd_oled_service_edit without options the service file will open in an editor, allowing the full service file to be changed, and not just the mpd_oled options.

If the mpd_oled options are valid the display will be started after the editor is closed, and will also be configured to start a boot

Check the program is working correctly by looking at the display while the player is stopped, paused and playing music.

Extra commands to control the service

A few selected commands that can be used to control the service

sudo systemctl enable mpd_oled    # start mpd_oled at boot
sudo systemctl disable mpd_oled   # don't start mpd_oled at boot
sudo systemctl start mpd_oled     # start mpd_oled now
sudo systemctl stop mpd_oled      # stop mpd_oled now
sudo systemctl status mpd_oled    # report the status of the service

Uninstall

Uninstall the mpd_oled service (just the service, not the mpd_oled programs or documentation), with

sudo mpd_oled_service_uninstall