Need help for Panasonic Remote Control N2QAYB000354

[stieneker]

I use IRrecvDUMPV2 with the remote and a TSMP58000.
Unfortunately, the program does not recognize the codes and constantly throws out codes that are unfortunately non-repeating, like these:
17:29:00.434 -> uint16_t rawData[1827] = {26, 6, 18, 8, 18, 6, 18, 6, 20, 8, 16, 10, 16, 8, 16, 10, 16, 8, 18, 8, 16, 8, 20, 8, 18, 8, 18, 8, 18, 10, 16, 10, 14, 10, 16, 10, 18, 8, 18, 6, 18, 8, 18, 10, 16, 8, 18, 6, 18, 6, 18, 10, 14, 10, 16, 8, 18, 6, 18, 10, 16, 10, 14, 10, 20, 8, 16, 8, 18, 6, 18, 6, 18, 10, 16, 8, 18, 6, 18, 10, 16, 10, 14, 10, 16, 10, 18, 8, 18, 8, 16, 8, 20, 8, 18, 8, 18, 8, 18, 8, 18, 10, 18, 6, 18, 6, 20, 10, 14, 10, 16, 8, 16, 10, 18, 8, 18, 8, 18, 8, 20, 6, 18, 6, 18, 6, 18, 8, 18, 8, 16, ... eingekürzt 24, 26, 8, 20, 26, 24, 28, 6, 18, 6, 18, 24, 6, 22, 4, 22, 24, 26, 26, 24, 6, 18, 4, 20, 8, 20, 24, 6, 1720, 6, 20, 6, 20, 26, 26, 6, 20, 26, 26, 8, 18, 6, 20, 24, 26, 6, 18, 6, 20, 26, 26, 6, 18, 6, 22, 24, 6, 18, 6, 22, 24, 582, 6, 20, 26, 8, 18, 6, 20, 26, 6, 18, 6, 20, 26, 24, 6, 18, 6, 22, 24, 26, 6, 18, 24, 6, 22, 26, 24, 6, 20, 4, 20, 30, 582, 4, 20, 26, 4, 22, 26, 6, 18, 24, 6, 22, 6, 18, 4, 22, 26, 26, 8, 18, 6, 20, 24, 26, 6, 20, 26, 24, 6, 22, 26, 26, 1726, 8, 18, 6, 20, 26, 26, 6, 18, 6, 20, 24, 8, 20, 24, 6, 18, 6, 20, 6, 20, 4, 20, 30, 22, 8, 18, 6, 20, 26, 26, 6, 22, 26, 1726, 26, 24, 26, 28, 26, 26, 26, 26, 6, 20, 24, 26, 6, 20, 26, 24, 6, 20, 6, 20, 26, 26, 26, 6, 18, 6, 20, 1726, 8, 18, 6, 20, 6, 18, 10, 18, 26, 4, 22, 24, 10, 18, 24, 6, 20, 4, 20, 8, 22, 24, 6, 20, 26, 6, 20, 4, 20, 6, 18, 10, 18, 26, 4, 22, 1724, 8, 20, 24, 4, 22, 26, 24, 6, 22, 26, 26, 6, 18, 26, 6, 18, 8, 20, 24, 4, 22, 24, 8, 20, 24, 26, 26, 6, 20, 4, 20}; // UNKNOWN 104AEAFE

I tried changing the timing, all to no avail.
What can I do?

[NiKiZe]

I would recommend reading the FAQ once more.
Check your wiring, my first guess would be that your input pin is floating, (or that you have not changed the pin in the program to the one being connected in your hardware)

[stieneker]

Hello, I have already read a lot on github and other forums about IRrecvDUMPV2. As far as I know the input pin is connected correctly. He also reacts to my remote control. The values ​​themselves are actually quite plausible. I compare this to a Saleae logic analyzer. The times are pretty good, but the evaluation.....?
Kind regards Manfred

[crankyoldgit]

The issue here is our library relies on a demodulated signal from IR demodulator receiver.
The IR sensor you're using is providing an Un-demodulated (modulated) output. (I looked up it's datasheet to confirm this)

For this library, you different type of IR receiver. See the main README.MD file.

[NiKiZe]

The timings looks of based on how IR signals usually look.
Try posting the actuall full message again.

In regards to the FAQ, here: https://github.com/crankyoldgit/IRremoteESP8266/wiki/Frequently-Asked-Questions#user-content-My_remotes_signal_is_being_reported_as_an_Unknown_code_What_does_that_mean_How_do_I_send_an_Unknown_code

[stieneker]

Hello, I found it. The error was due to the wrong IR module. It must definitely be a PCM-suitable module. Only they have fast enough flank changes. Now the names, commands, etc. are recognized directly! I would especially like to thank Crankyoldkit for the tips! I am happy.
Greetings Manfred