carbide3d-crpalmer.cps

/**
  Copyright (C) 2012-2022 by Autodesk, Inc.
  All rights reserved.

  Carbide 3D Grbl post processor configuration.

  $Revision: 43777 ff938d4771883144ce8a48c0567d8814618df70b $
  $Date: 2022-04-21 16:47:31 $

  FORKID {D897E9AA-349A-4011-AA01-06B6CCC181EB}
*/

description = "Carbide 3D by crpalmer (Grbl)";
vendor = "Carbide 3D";
vendorUrl = "http://www.carbide3d.com";
legal = "Copyright (C) 2012-2022 by Autodesk, Inc. Modified by crpalmer@gmail.com.";
certificationLevel = 2;
minimumRevision = 45702;

longDescription = "Milling post for Carbide 3D (Grbl) extended by crpalmer.";

extension = "nc";
setCodePage("ascii");

capabilities = CAPABILITY_MILLING;
tolerance = spatial(0.002, MM);

minimumChordLength = spatial(0.25, MM);
minimumCircularRadius = spatial(0.1, MM);
maximumCircularRadius = spatial(1000, MM);
minimumCircularSweep = toRad(0.01);
maximumCircularSweep = toRad(180);
allowHelicalMoves = true;
allowedCircularPlanes = undefined; // allow any circular motion

// user-defined properties
properties = {
  writeMachine: {
    title      : "Write machine",
    description: "Output the machine settings in the header of the code.",
    group      : "formats",
    type       : "boolean",
    value      : true,
    scope      : "post"
  },
  writeTools: {
    title      : "Write tool list",
    description: "Output a tool list in the header of the code.",
    group      : "formats",
    type       : "boolean",
    value      : true,
    scope      : "post"
  },
  showSequenceNumbers: {
    title      : "Use sequence numbers",
    description: "'Yes' outputs sequence numbers on each block, 'Only on tool change' outputs sequence numbers on tool change blocks only, and 'No' disables the output of sequence numbers.",
    group      : "formats",
    type       : "enum",
    values     : [
      {title:"Yes", id:"true"},
      {title:"No", id:"false"},
      {title:"Only on tool change", id:"toolChange"}
    ],
    value: "false",
    scope: "post"
  },
  sequenceNumberStart: {
    title      : "Start sequence number",
    description: "The number at which to start the sequence numbers.",
    group      : "formats",
    type       : "integer",
    value      : 10,
    scope      : "post"
  },
  sequenceNumberIncrement: {
    title      : "Sequence number increment",
    description: "The amount by which the sequence number is incremented by in each block.",
    group      : "formats",
    type       : "integer",
    value      : 1,
    scope      : "post"
  },
  separateWordsWithSpace: {
    title      : "Separate words with space",
    description: "Adds spaces between words if 'yes' is selected.",
    group      : "formats",
    type       : "boolean",
    value      : true,
    scope      : "post"
  },
  safePositionMethod: {
    title      : "Safe Retracts",
    description: "Select your desired retract option. 'Clearance Height' retracts to the operation clearance height.",
    group      : "homePositions",
    type       : "enum",
    values     : [
      {title:"G28", id:"G28"},
      // {title:"G53", id: "G53"},
      {title:"Clearance Height", id:"clearanceHeight"}
    ],
    value: "G28",
    scope: "post"
  },
  manualSpindleControl: {
    title      : "Manual speed changes",
    description: "Add pause commands (M0) to allow you to perform manual spindle speed changes.  This includes a comment indicating the required changed which works well with CNCjs / gSender.",
    group      : "spindle",
    type       : "boolean",
    value      : false,
    scope      : "post"
  },
  spindleControlDwellSeconds: {
    title      : "Speed change pause seconds",
    description: "Add a dwell command to pause for the specified number of seconds whenever the spindle speed changes.",
    group      : "spindle",
    type       : "number",
    value      : 0,
    scope      : "post"
  },
};

groupDefinitions = {
  spindle: {title: "Spindle Control", description: "Spindle control options", collapsed:false, order:1},
  };
// wcs definiton
wcsDefinitions = {
  useZeroOffset: false,
  wcs          : [
    {name:"Standard", format:"G", range:[54, 59]}
  ]
};

var numberOfToolSlots = 9999;

var singleLineCoolant = false; // specifies to output multiple coolant codes in one line rather than in separate lines
// samples:
// {id: COOLANT_THROUGH_TOOL, on: 88, off: 89}
// {id: COOLANT_THROUGH_TOOL, on: [8, 88], off: [9, 89]}
// {id: COOLANT_THROUGH_TOOL, on: "M88 P3 (myComment)", off: "M89"}
var coolants = [
  {id:COOLANT_FLOOD, on:7},
  {id:COOLANT_MIST},
  {id:COOLANT_THROUGH_TOOL},
  {id:COOLANT_AIR},
  {id:COOLANT_AIR_THROUGH_TOOL},
  {id:COOLANT_SUCTION},
  {id:COOLANT_FLOOD_MIST},
  {id:COOLANT_FLOOD_THROUGH_TOOL},
  {id:COOLANT_OFF, off:9}
];

var gFormat = createFormat({prefix:"G", decimals:0});
var mFormat = createFormat({prefix:"M", decimals:0});

var xyzFormat = createFormat({decimals:(unit == MM ? 3 : 4)});
var feedFormat = createFormat({decimals:(unit == MM ? 2 : 3)});
var toolFormat = createFormat({decimals:0});
var rpmFormat = createFormat({decimals:0});
var secFormat = createFormat({decimals:3, forceDecimal:true}); // seconds - range 0.001-1000
var taperFormat = createFormat({decimals:1, scale:DEG});

var xOutput = createVariable({prefix:"X"}, xyzFormat);
var yOutput = createVariable({prefix:"Y"}, xyzFormat);
var zOutput = createVariable({onchange:function() {retracted = false;}, prefix:"Z"}, xyzFormat);
var feedOutput = createVariable({prefix:"F"}, feedFormat);
var sOutput = createVariable({prefix:"S", force:true}, rpmFormat);

// circular output
var iOutput = createReferenceVariable({prefix:"I", force:true}, xyzFormat);
var jOutput = createReferenceVariable({prefix:"J", force:true}, xyzFormat);
var kOutput = createReferenceVariable({prefix:"K", force:true}, xyzFormat);

var gMotionModal = createModal({}, gFormat); // modal group 1 // G0-G3, ...
var gPlaneModal = createModal({onchange:function () {gMotionModal.reset();}}, gFormat); // modal group 2 // G17-19
var gAbsIncModal = createModal({}, gFormat); // modal group 3 // G90-91
var gUnitModal = createModal({}, gFormat); // modal group 6 // G20-21

var WARNING_WORK_OFFSET = 0;

// collected state
var sequenceNumber;
var forceSpindleSpeed = false;
var currentWorkOffset;
var retracted = false; // specifies that the tool has been retracted to the safe plane

/**
  Writes the specified block.
*/
function writeBlock() {
  var text = formatWords(arguments);
  if (!text) {
    return;
  }
  if (getProperty("showSequenceNumbers") == "true") {
    writeWords2("N" + sequenceNumber, arguments);
    sequenceNumber += getProperty("sequenceNumberIncrement");
  } else {
    writeWords(arguments);
  }
}

function formatComment(text) {
  return "(" + String(text).replace(/[()]/g, "") + ")";
}

/**
  Writes the specified block - used for tool changes only.
*/
function writeToolBlock() {
  var show = getProperty("showSequenceNumbers");
  setProperty("showSequenceNumbers", (show == "true" || show == "toolChange") ? "true" : "false");
  writeBlock(arguments);
  setProperty("showSequenceNumbers", show);
}

/**
  Output a comment.
*/
function writeComment(text) {
  writeln(formatComment(text));
}

function onOpen() {
  if (!getProperty("separateWordsWithSpace")) {
    setWordSeparator("");
  }

  sequenceNumber = getProperty("sequenceNumberStart");
  writeln("%");

  for (let i = 1; i <= 10; i++) {
    if (i == 5) writeln(";     gSender eats any M0 commands in the first 10 lines of the gcode!!");
    else writeln(";" + i);
  }

  if (programName) {
    writeComment(programName);
  }
  if (programComment) {
    writeComment(programComment);
  }

  // dump machine configuration
  var vendor = machineConfiguration.getVendor();
  var model = machineConfiguration.getModel();
  var description = machineConfiguration.getDescription();

  if (getProperty("writeMachine") && (vendor || model || description)) {
    writeComment(localize("Machine"));
    if (vendor) {
      writeComment("  " + localize("vendor") + ": " + vendor);
    }
    if (model) {
      writeComment("  " + localize("model") + ": " + model);
    }
    if (description) {
      writeComment("  " + localize("description") + ": "  + description);
    }
  }

  // dump tool information
  if (getProperty("writeTools")) {
    var zRanges = {};
    if (is3D()) {
      var numberOfSections = getNumberOfSections();
      for (var i = 0; i < numberOfSections; ++i) {
        var section = getSection(i);
        var zRange = section.getGlobalZRange();
        var tool = section.getTool();
        if (zRanges[tool.number]) {
          zRanges[tool.number].expandToRange(zRange);
        } else {
          zRanges[tool.number] = zRange;
        }
      }
    }

    var tools = getToolTable();
    if (tools.getNumberOfTools() > 0) {
      for (var i = 0; i < tools.getNumberOfTools(); ++i) {
        var tool = tools.getTool(i);
        var comment = "T" + toolFormat.format(tool.number) + "  " +
          "D=" + xyzFormat.format(tool.diameter) + " " +
          localize("CR") + "=" + xyzFormat.format(tool.cornerRadius);
        if ((tool.taperAngle > 0) && (tool.taperAngle < Math.PI)) {
          comment += " " + localize("TAPER") + "=" + taperFormat.format(tool.taperAngle) + localize("deg");
        }
        if (zRanges[tool.number]) {
          comment += " - " + localize("ZMIN") + "=" + xyzFormat.format(zRanges[tool.number].getMinimum());
        }
        comment += " - " + getToolTypeName(tool.type);
        writeComment(comment);
      }
    }
  }

  if ((getNumberOfSections() > 0) && (getSection(0).workOffset == 0)) {
    for (var i = 0; i < getNumberOfSections(); ++i) {
      if (getSection(i).workOffset > 0) {
        error(localize("Using multiple work offsets is not possible if the initial work offset is 0."));
        return;
      }
    }
  }

  // absolute coordinates and feed per min
  writeBlock(gAbsIncModal.format(90));
  writeBlock(gPlaneModal.format(17));

  switch (unit) {
  case IN:
    writeBlock(gUnitModal.format(20));
    break;
  case MM:
    writeBlock(gUnitModal.format(21));
    break;
  }
}

function onComment(message) {
  writeComment(message);
}

/** Force output of X, Y, and Z. */
function forceXYZ() {
  xOutput.reset();
  yOutput.reset();
  zOutput.reset();
}

/** Force output of X, Y, Z, and F on next output. */
function forceAny() {
  forceXYZ();
  feedOutput.reset();
}

function isProbeOperation() {
  return hasParameter("operation-strategy") && (getParameter("operation-strategy") == "probe");
}

function onSection() {
  var insertToolCall = isFirstSection() ||
    currentSection.getForceToolChange && currentSection.getForceToolChange() ||
    (tool.number != getPreviousSection().getTool().number);

  retracted = false;
  var newWorkOffset = isFirstSection() ||
    (getPreviousSection().workOffset != currentSection.workOffset); // work offset changes
  var newWorkPlane = isFirstSection() ||
    !isSameDirection(getPreviousSection().getGlobalFinalToolAxis(), currentSection.getGlobalInitialToolAxis()) ||
    (currentSection.isOptimizedForMachine() && getPreviousSection().isOptimizedForMachine() &&
      Vector.diff(getPreviousSection().getFinalToolAxisABC(), currentSection.getInitialToolAxisABC()).length > 1e-4) ||
    (!machineConfiguration.isMultiAxisConfiguration() && currentSection.isMultiAxis()) ||
    (!getPreviousSection().isMultiAxis() && currentSection.isMultiAxis() ||
      getPreviousSection().isMultiAxis() && !currentSection.isMultiAxis()); // force newWorkPlane between indexing and simultaneous operations
  if (insertToolCall || newWorkOffset || newWorkPlane) {

    // stop spindle before retract during tool change
    if (insertToolCall && !isFirstSection()) {
      onCommand(COMMAND_STOP_SPINDLE);
    }

    // retract to safe plane
    writeRetract(Z);
    zOutput.reset();
  }

  writeln("");

  if (hasParameter("operation-comment")) {
    var comment = getParameter("operation-comment");
    if (comment) {
      writeComment(comment);
    }
  }

  if (insertToolCall) {
    setCoolant(COOLANT_OFF);

    if (tool.number > numberOfToolSlots) {
      warning(localize("Tool number exceeds maximum value."));
    }

    var pieces = [ "; tool #" + tool.number ];
    if (tool.description != null && tool.description !== '') {
      pieces.push(tool.description);
    }
    if (tool.comment != null && tool.comment !== '') {
      pieces.push(tool.comment);
    }
    var comment = pieces.join(' / ');

    writeToolBlock("T" + toolFormat.format(tool.number), mFormat.format(6), comment);
    var showToolZMin = false;
    if (showToolZMin) {
      if (is3D()) {
        var numberOfSections = getNumberOfSections();
        var zRange = currentSection.getGlobalZRange();
        var number = tool.number;
        for (var i = currentSection.getId() + 1; i < numberOfSections; ++i) {
          var section = getSection(i);
          if (section.getTool().number != number) {
            break;
          }
          zRange.expandToRange(section.getGlobalZRange());
        }
        writeComment(localize("ZMIN") + "=" + zRange.getMinimum());
      }
    }
  }

  var spindleChanged = tool.type != TOOL_PROBE &&
    (insertToolCall || forceSpindleSpeed || isFirstSection() ||
    (rpmFormat.areDifferent(spindleSpeed, sOutput.getCurrent())) ||
    (tool.clockwise != getPreviousSection().getTool().clockwise));
  if (spindleChanged) {
    forceSpindleSpeed = false;
    if (spindleSpeed < 1) {
      error(localize("Spindle speed out of range."));
    }
    if (spindleSpeed > 99999) {
      warning(localize("Spindle speed exceeds maximum value."));
    }
    writeBlock(sOutput.format(spindleSpeed));
    onCommand(COMMAND_START_SPINDLE);
  }

  // wcs
  if (insertToolCall) { // force work offset when changing tool
    currentWorkOffset = undefined;
  }

  if (currentSection.workOffset != currentWorkOffset) {
    writeBlock(currentSection.wcs);
    currentWorkOffset = currentSection.workOffset;
  }

  forceXYZ();

  { // pure 3D
    var remaining = currentSection.workPlane;
    if (!isSameDirection(remaining.forward, new Vector(0, 0, 1))) {
      error(localize("Tool orientation is not supported."));
      return;
    }
    setRotation(remaining);
  }

  // set coolant after we have positioned at Z
  setCoolant(tool.coolant);

  forceAny();

  var initialPosition = getFramePosition(currentSection.getInitialPosition());
  if (!retracted && !insertToolCall) {
    if (getCurrentPosition().z < initialPosition.z) {
      writeBlock(gMotionModal.format(0), zOutput.format(initialPosition.z));
    }
  }

  if (insertToolCall || retracted) {
    var lengthOffset = tool.lengthOffset;
    if (lengthOffset > numberOfToolSlots) {
      error(localize("Length offset out of range."));
      return;
    }

    gMotionModal.reset();
    writeBlock(gPlaneModal.format(17));

    if (!machineConfiguration.isHeadConfiguration()) {
      writeBlock(
        gAbsIncModal.format(90),
        gMotionModal.format(0), xOutput.format(initialPosition.x), yOutput.format(initialPosition.y)
      );
      writeBlock(gMotionModal.format(0), zOutput.format(initialPosition.z));
    } else {
      writeBlock(
        gAbsIncModal.format(90),
        gMotionModal.format(0),
        xOutput.format(initialPosition.x),
        yOutput.format(initialPosition.y),
        zOutput.format(initialPosition.z)
      );
    }
  } else {
    writeBlock(
      gAbsIncModal.format(90),
      gMotionModal.format(0),
      xOutput.format(initialPosition.x),
      yOutput.format(initialPosition.y)
    );
  }
}

function onDwell(seconds) {
  if (seconds > 99999.999) {
    warning(localize("Dwelling time is out of range."));
  }
  seconds = clamp(0.001, seconds, 99999.999);
  writeBlock(gFormat.format(4), "P" + secFormat.format(seconds));
}

function onSpindleSpeed(spindleSpeed) {
  writeBlock(sOutput.format(spindleSpeed));
}

var pendingRadiusCompensation = -1;

function onRadiusCompensation() {
  pendingRadiusCompensation = radiusCompensation;
}

function onRapid(_x, _y, _z) {
  var x = xOutput.format(_x);
  var y = yOutput.format(_y);
  var z = zOutput.format(_z);
  if (x || y || z) {
    if (pendingRadiusCompensation >= 0) {
      error(localize("Radius compensation mode cannot be changed at rapid traversal."));
      return;
    }
    writeBlock(gMotionModal.format(0), x, y, z);
    feedOutput.reset();
  }
}

function onLinear(_x, _y, _z, feed) {
  // at least one axis is required
  if (pendingRadiusCompensation >= 0) {
    // ensure that we end at desired position when compensation is turned off
    xOutput.reset();
    yOutput.reset();
  }
  var x = xOutput.format(_x);
  var y = yOutput.format(_y);
  var z = zOutput.format(_z);
  var f = feedOutput.format(feed);
  if (x || y || z) {
    if (pendingRadiusCompensation >= 0) {
      error(localize("Radius compensation mode is not supported."));
      return;
    } else {
      writeBlock(gMotionModal.format(1), x, y, z, f);
    }
  } else if (f) {
    if (getNextRecord().isMotion()) { // try not to output feed without motion
      feedOutput.reset(); // force feed on next line
    } else {
      writeBlock(gMotionModal.format(1), f);
    }
  }
}

function onRapid5D(_x, _y, _z, _a, _b, _c) {
  error(localize("Multi-axis motion is not supported."));
}

function onLinear5D(_x, _y, _z, _a, _b, _c, feed) {
  error(localize("Multi-axis motion is not supported."));
}

/** Adjust final point to lie exactly on circle. */
function CircularData(_plane, _center, _end) {
  // use Output variables, since last point could have been adjusted if previous move was circular
  var start = new Vector(xOutput.getCurrent(), yOutput.getCurrent(), zOutput.getCurrent());
  var saveStart = new Vector(start.x, start.y, start.z);
  var center = new Vector(
    xyzFormat.getResultingValue(_center.x),
    xyzFormat.getResultingValue(_center.y),
    xyzFormat.getResultingValue(_center.z)
  );
  var end = new Vector(_end.x, _end.y, _end.z);
  switch (_plane) {
  case PLANE_XY:
    start.setZ(center.z);
    end.setZ(center.z);
    break;
  case PLANE_ZX:
    start.setY(center.y);
    end.setY(center.y);
    break;
  case PLANE_YZ:
    start.setX(center.x);
    end.setX(center.x);
    break;
  default:
    this.center = new Vector(_center.x, _center.y, _center.z);
    this.start = new Vector(start.x, start.y, start.z);
    this.end = new Vector(_end.x, _end.y, _end.z);
    this.offset = Vector.diff(center, start);
    this.radius = this.offset.length;
  }
  this.start = new Vector(
    xyzFormat.getResultingValue(start.x),
    xyzFormat.getResultingValue(start.y),
    xyzFormat.getResultingValue(start.z)
  );
  var temp = Vector.diff(center, start);
  this.offset = new Vector(
    xyzFormat.getResultingValue(temp.x),
    xyzFormat.getResultingValue(temp.y),
    xyzFormat.getResultingValue(temp.z)
  );
  this.center = Vector.sum(this.start, this.offset);
  this.radius = this.offset.length;

  temp = Vector.diff(end, center).normalized;
  this.end = new Vector(
    xyzFormat.getResultingValue(this.center.x + temp.x * this.radius),
    xyzFormat.getResultingValue(this.center.y + temp.y * this.radius),
    xyzFormat.getResultingValue(this.center.z + temp.z * this.radius)
  );

  switch (_plane) {
  case PLANE_XY:
    this.start.setZ(saveStart.z);
    this.end.setZ(_end.z);
    this.offset.setZ(0);
    break;
  case PLANE_ZX:
    this.start.setY(saveStart.y);
    this.end.setY(_end.y);
    this.offset.setY(0);
    break;
  case PLANE_YZ:
    this.start.setX(saveStart.x);
    this.end.setX(_end.x);
    this.offset.setX(0);
    break;
  }
}

function onCircular(clockwise, cx, cy, cz, x, y, z, feed) {
  // one of X/Y and I/J are required and likewise

  if (pendingRadiusCompensation >= 0) {
    error(localize("Radius compensation cannot be activated/deactivated for a circular move."));
    return;
  }

  circle = new CircularData(getCircularPlane(), new Vector(cx, cy, cz), new Vector(x, y, z));

  if (isFullCircle()) {
    if (isHelical()) {
      linearize(tolerance);
      return;
    }
    // TAG: are 360deg arcs supported
    switch (getCircularPlane()) {
    case PLANE_XY:
      writeBlock(gPlaneModal.format(17), gMotionModal.format(clockwise ? 2 : 3), xOutput.format(circle.end.x), iOutput.format(circle.offset.x, 0), jOutput.format(circle.offset.y, 0), feedOutput.format(feed));
      break;
    case PLANE_ZX:
      writeBlock(gPlaneModal.format(18), gMotionModal.format(clockwise ? 2 : 3), zOutput.format(circle.end.z), iOutput.format(circle.offset.x, 0), kOutput.format(circle.offset.z, 0), feedOutput.format(feed));
      break;
    case PLANE_YZ:
      writeBlock(gPlaneModal.format(19), gMotionModal.format(clockwise ? 2 : 3), yOutput.format(circle.end.y), jOutput.format(circle.offset.y, 0), kOutput.format(circle.offset.z, 0), feedOutput.format(feed));
      break;
    default:
      linearize(tolerance);
    }
  } else {
    switch (getCircularPlane()) {
    case PLANE_XY:
      writeBlock(gPlaneModal.format(17), gMotionModal.format(clockwise ? 2 : 3),
        xOutput.format(circle.end.x), yOutput.format(circle.end.y), zOutput.format(circle.end.z),
        iOutput.format(circle.offset.x, 0), jOutput.format(circle.offset.y, 0), feedOutput.format(feed));
      break;
    case PLANE_ZX:
      writeBlock(gPlaneModal.format(18), gMotionModal.format(clockwise ? 2 : 3),
        xOutput.format(circle.end.x), yOutput.format(circle.end.y), zOutput.format(circle.end.z),
        iOutput.format(circle.offset.x, 0), kOutput.format(circle.offset.z, 0), feedOutput.format(feed));
      break;
    case PLANE_YZ:
      writeBlock(gPlaneModal.format(19), gMotionModal.format(clockwise ? 2 : 3),
        xOutput.format(circle.end.x), yOutput.format(circle.end.y), zOutput.format(circle.end.z),
        jOutput.format(circle.offset.y, 0), kOutput.format(circle.offset.z, 0), feedOutput.format(feed));
      break;
    default:
      linearize(tolerance);
    }
  }
}

var currentCoolantMode = COOLANT_OFF;
var coolantOff = undefined;
var forceCoolant = false;

function setCoolant(coolant) {
  var coolantCodes = getCoolantCodes(coolant);
  if (Array.isArray(coolantCodes)) {
    if (singleLineCoolant) {
      writeBlock(coolantCodes.join(getWordSeparator()));
    } else {
      for (var c in coolantCodes) {
        writeBlock(coolantCodes[c]);
      }
    }
    return undefined;
  }
  return coolantCodes;
}

function getCoolantCodes(coolant) {
  var multipleCoolantBlocks = new Array(); // create a formatted array to be passed into the outputted line
  if (!coolants) {
    error(localize("Coolants have not been defined."));
  }
  if (tool.type == TOOL_PROBE) { // avoid coolant output for probing
    coolant = COOLANT_OFF;
  }
  if (coolant == currentCoolantMode && (!forceCoolant || coolant == COOLANT_OFF)) {
    return undefined; // coolant is already active
  }
  if ((coolant != COOLANT_OFF) && (currentCoolantMode != COOLANT_OFF) && (coolantOff != undefined) && !forceCoolant) {
    if (Array.isArray(coolantOff)) {
      for (var i in coolantOff) {
        multipleCoolantBlocks.push(coolantOff[i]);
      }
    } else {
      multipleCoolantBlocks.push(coolantOff);
    }
  }
  forceCoolant = false;

  var m;
  var coolantCodes = {};
  for (var c in coolants) { // find required coolant codes into the coolants array
    if (coolants[c].id == coolant) {
      coolantCodes.on = coolants[c].on;
      if (coolants[c].off != undefined) {
        coolantCodes.off = coolants[c].off;
        break;
      } else {
        for (var i in coolants) {
          if (coolants[i].id == COOLANT_OFF) {
            coolantCodes.off = coolants[i].off;
            break;
          }
        }
      }
    }
  }
  if (coolant == COOLANT_OFF) {
    m = !coolantOff ? coolantCodes.off : coolantOff; // use the default coolant off command when an 'off' value is not specified
  } else {
    coolantOff = coolantCodes.off;
    m = coolantCodes.on;
  }

  if (!m) {
    onUnsupportedCoolant(coolant);
    m = 9;
  } else {
    if (Array.isArray(m)) {
      for (var i in m) {
        multipleCoolantBlocks.push(m[i]);
      }
    } else {
      multipleCoolantBlocks.push(m);
    }
    currentCoolantMode = coolant;
    for (var i in multipleCoolantBlocks) {
      if (typeof multipleCoolantBlocks[i] == "number") {
        multipleCoolantBlocks[i] = mFormat.format(multipleCoolantBlocks[i]);
      }
    }
    return multipleCoolantBlocks; // return the single formatted coolant value
  }
  return undefined;
}

var mapCommand = {
  COMMAND_STOP                    : 0,
  COMMAND_END                     : 2,
  COMMAND_SPINDLE_CLOCKWISE       : 3,
  COMMAND_SPINDLE_COUNTERCLOCKWISE: 4,
  COMMAND_STOP_SPINDLE            : 5
};

function writeStopSpindlePause() {
  writeBlock(mFormat.format(0), "; Turn off the spindle");
}

function onCommand(command) {
  switch (command) {
  case COMMAND_STOP:
    writeBlock(mFormat.format(0));
    forceSpindleSpeed = true;
    forceCoolant = true;
    return;
  case COMMAND_START_SPINDLE:
    onCommand(tool.clockwise ? COMMAND_SPINDLE_CLOCKWISE : COMMAND_SPINDLE_COUNTERCLOCKWISE);
    return;
  case COMMAND_LOCK_MULTI_AXIS:
    return;
  case COMMAND_UNLOCK_MULTI_AXIS:
    return;
  case COMMAND_BREAK_CONTROL:
    return;
  case COMMAND_TOOL_MEASURE:
    return;
  }

  var stringId = getCommandStringId(command);
  var mcode = mapCommand[stringId];

  if (mcode != undefined) {
    if (getProperty("manualSpindleControl")) {
      if (mcode == 5) {
        writeStopSpindlePause();
      } else {
        writeBlock(mFormat.format(0), "; Set spindle speed to " + spindleSpeed + " rpm: " + (tool.clockwise ? "" : "C") + "CW ");
      }
    }
    writeBlock(mFormat.format(mcode));
    let dwellSeconds = getProperty("spindleControlDwellSeconds");
    if (dwellSeconds > 0) {
      onDwell(dwellSeconds);
    }
  } else {
    onUnsupportedCommand(command);
  }
}

function onSectionEnd() {
  writeBlock(gPlaneModal.format(17));
  if (!isLastSection() && (getNextSection().getTool().coolant != tool.coolant)) {
    setCoolant(COOLANT_OFF);
  }
  forceAny();
}

/** Output block to do safe retract and/or move to home position. */
function writeRetract() {
  var words = []; // store all retracted axes in an array
  var retractAxes = new Array(false, false, false);
  var method = getProperty("safePositionMethod");
  if (method == "clearanceHeight") {
    if (!is3D()) {
      error(localize("Safe retract option 'Clearance Height' is only supported when all operations are along the setup Z-axis."));
    }
    return;
  }
  validate(arguments.length != 0, "No axis specified for writeRetract().");

  for (i in arguments) {
    retractAxes[arguments[i]] = true;
  }
  if ((retractAxes[0] || retractAxes[1]) && !retracted) { // retract Z first before moving to X/Y home
    error(localize("Retracting in X/Y is not possible without being retracted in Z."));
    return;
  }
  // special conditions
  /*
  if (retractAxes[2]) { // Z doesn't use G53
    method = "G28";
  }
  */

  // define home positions
  var _xHome;
  var _yHome;
  var _zHome;
  if (method == "G28") {
    _xHome = toPreciseUnit(0, MM);
    _yHome = toPreciseUnit(0, MM);
    _zHome = toPreciseUnit(0, MM);
  } else {
    _xHome = machineConfiguration.hasHomePositionX() ? machineConfiguration.getHomePositionX() : toPreciseUnit(0, MM);
    _yHome = machineConfiguration.hasHomePositionY() ? machineConfiguration.getHomePositionY() : toPreciseUnit(0, MM);
    _zHome = machineConfiguration.getRetractPlane() != 0 ? machineConfiguration.getRetractPlane() : toPreciseUnit(0, MM);
  }
  for (var i = 0; i < arguments.length; ++i) {
    switch (arguments[i]) {
    case X:
      words.push("X" + xyzFormat.format(_xHome));
      xOutput.reset();
      break;
    case Y:
      words.push("Y" + xyzFormat.format(_yHome));
      yOutput.reset();
      break;
    case Z:
      words.push("Z" + xyzFormat.format(_zHome));
      zOutput.reset();
      retracted = true;
      break;
    default:
      error(localize("Unsupported axis specified for writeRetract()."));
      return;
    }
  }
  if (words.length > 0) {
    switch (method) {
    case "G28":
      gMotionModal.reset();
      gAbsIncModal.reset();
      writeBlock(gFormat.format(28), gAbsIncModal.format(91), words);
      writeBlock(gAbsIncModal.format(90));
      break;
    case "G53":
      gMotionModal.reset();
      writeBlock(gAbsIncModal.format(90), gFormat.format(53), gMotionModal.format(0), words);
      break;
    default:
      error(localize("Unsupported safe position method."));
      return;
    }
  }
}

function onClose() {
  setCoolant(COOLANT_OFF);

  writeRetract(Z); // retract

  if (getProperty("manualSpindleControl")) {
    writeStopSpindlePause();
  }

  writeRetract(X, Y);

  onImpliedCommand(COMMAND_END);
  onImpliedCommand(COMMAND_STOP_SPINDLE);
  writeBlock(mFormat.format(30)); // stop program, spindle stop, coolant off
  writeln("%");
}

function setProperty(property, value) {
  properties[property].current = value;
}