OneWireNg

This is an 1-wire service library, intended as an alternative for the classic OneWire library. The library provides basic 1-wire services (reset, search, touch, read, write, parasite powering) and may serve for further work while interfacing with various 1-wire devices.

Features

All bus activities are performed respecting open-drain character of the 1-wire protocol.

During normal 1-wire activities, the master MCU GPIO controlling the bus is never set high (providing direct voltage source on the bus) instead the GPIO is switched to the reading mode causing the high state seen on the bus via the pull-up resistor.
1-wire touch support.

The 1-wire touch may substantially simplify complex bus activities consisting of write-read pairs by combining them into a single touch activity. See examples for details.
Parasite powering support.

The 1-wire bus may be powered directly by the master MCU GPIO or via a switching transistor controlled by a dedicated MCU GPIO. More details below.
Search filtering.

Search algorithm allows efficient filtering basing on a selected set of family codes. Maximum size of the set is configurable by CONFIG_MAX_SEARCH_FILTERS.
Overdrive (high-speed) mode support.

The overdrive mode enables speed up the 1-wire communication by a factor of 10. Only limited number of 1-wire devices support this mode (e.g. DS2408, DS2431).
Dallas temperature sensors drivers.

Generic Dallas thermometers and MAX31850/MAX31851 drivers for handling Dallas thermometers and thermocouples. See examples for details.
OneWire compatibility interface.

The interface allows effortless switch into OneWireNg for projects using OneWire library. See below for details.
Clear and flexible architecture.

The code architecture allows fast and easy porting for new Arduino platforms or even usage core part of the library outside the Arduino environment. See below for usage details on ESP-IDF, Pico SDK or Mbed OS based platforms.

Usage

Refer to examples directory for usage details for each of the supported frameworks: Arduino, ESP-IDF, Pico SDK and Mbed.

For API specification refer to sources inline documentation (mainly OneWireNg class). For convenience it's possible to generate HTML/LaTeX Doxygen documentation by issuing doxygen from the main library directory. The documentation will be placed in extras/doc.

File src/OneWireNg_Config.h contains parameters configuring the library functionality. See the file for more details.

ESP-IDF (incl. ESP8266 RTOS SDK v3)

Preferred way to add OneWireNg as a library for Espressif ESP-IDF framework is to add it as a git submodule located at project's components subdirectory:

git submodule add -- https://github.com/pstolarz/OneWireNg components/OneWireNg

Next checkout specific library VERSION:

cd components/OneWireNg
git checkout VERSION

While added the library shall be configured via ESP-IDF native configuration (see Kconfig for details), which shadows the OneWireNg_Config.h configuration file.

Pico SDK

Preferred way to add OneWireNg as a library for Raspberry Pi Pico SDK framework is to add it as a git submodule:

git submodule add -- https://github.com/pstolarz/OneWireNg OneWireNg

Checkout on a specific library VERSION:

cd OneWireNg
git checkout VERSION

Finally add OneWireNg as a library in a Pico SDK project's CMakeLists.txt file as follows:

cmake_minimum_required(VERSION 3.13)
include(pico_sdk_import.cmake)

project(some_project)
pico_sdk_init()

add_executable(some_project)

...

add_subdirectory(OneWireNg)
target_link_libraries(some_project PRIVATE OneWireNg)

pico_add_extra_outputs(some_project)

Mbed OS

NOTE: The library usage for Mbed OS is experimental. The only board used for tests of this framework is NUCLEO-L552ZE-Q.

To add OneWireNg as a library for Mbed framework project use (for specific VERSION):

mbed add https://github.com/pstolarz/OneWireNg#VERSION

While added the library shall be configured via Mbed native configuration (see mbed_lib.json for details), which shadows the OneWireNg_Config.h configuration file.

Supported platforms

Arduino AVR.
- Platform class: OneWireNg_ArduinoAVR.
- Tested on Arduino UNO (ATmega328P).
Arduino megaAVR (recent Microchip AVR architecture).
- Platform class: OneWireNg_ArduinoMegaAVR.
- Reported to be working.
Arduino ESP8266/ESP-IDF.
- Platform class: OneWireNg_ArduinoIdfESP8266.
- Tested on WemOS D1.
Arduino/ESP-IDF ESP32 (classic, S, C, H and P families).
- Platform class: OneWireNg_ArduinoIdfESP32.
- Tested on ESP32-WROOM-32, ESP32-S2-WROVER, ESP32-S3-WROOM-1, ESP32-C3-32S-Kit.
Arduino/Pico SDK RP2040.
- Platform classes: OneWireNg_PicoRP2040, OneWireNg_PicoRP2040PIO.
- Tested on Raspberry Pi Pico.
Arduino/Mbed OS based platforms (incl. Edge, Giga, Nano, Nicla, Portena, RP2040).
- Platform class: OneWireNg_ArduinoMbedHAL.
- Tested on Raspberry Pi Pico, Nucleo-144 (L552ZE-Q).
Arduino STM32.
- Platform class: OneWireNg_ArduinoSTM32.
- Tested on Nucleo-144 (L552ZE-Q).
Arduino SAM.
- Platform class: OneWireNg_ArduinoSAM.
- Reported to be working.
Arduino SAMD/SAMD-Beta.
- Platform class: OneWireNg_ArduinoSAMD.
- Not tested.

NOTE: Expect more platforms support in the future. I'm inviting all developers eager to help me with porting and testing the library for new platforms.

Overdrive mode

When configured with CONFIG_OVERDRIVE_ENABLED the library supports 1-wire overdrive mode. The mode requires very strict and short timings while bit-banging data on the 1-wire bus, therefore is vulnerable for any inaccuracies.

While configured with CONFIG_BITBANG_DELAY_CCOUNT the mode is confirmed to work on the following platforms and CPU frequencies:

AVR
- Arduino UNO (ATmega328P); 16MHz.
ESP8266
- WemOS D1; 160,80MHz.
ESP32
- ESP32-WROOM-32; 240,160,80,40,20MHz
- ESP32-S2-WROVER; 240,160,80,40,20,10MHz
- ESP32-S3-WROOM-1; 240,160,80MHz (other freqs not tested)
- ESP32-C3-32S-Kit; 240,160MHz (other freqs not tested)
RP2040
- Raspberry Pi Pico; 50-250MHz (bit-banging and PIO drivers)
STM32
- NUCLEO-L552ZE-Q; 110MHz

Parasite powering

Bit-banging drivers

For bit-banging type of drivers, the library supports two modes of providing a direct voltage source on the 1-wire bus for parasitically powered slaves:

If platform's GPIO set to the high-state (in the output mode) is able to serve as a voltage source, the library may leverage this trait. The master MCU GPIO controlling the 1-wire bus is set to the high-state powering the bus when additional energy is needed for connected slaves.
If platform's GPIO is of an open-drain type, then a GPIO is not able to directly serve as a voltage source powering the connected slaves. In this case an additional switching transistor is leveraged to control providing an external power source to the bus and is controlled by a dedicated power-control-GPIO as presented on the following figure.

To enable the second mode the library needs to be configured with CONFIG_PWR_CTRL_ENABLED.

Choice between the two types is made by selecting appropriate constructor of a platform class. For example:

#include "OneWireNg_CurrentPlatform.h"

static OneWireNg *ow = NULL;

void setup()
{
    /*
     * Macro-defines used:
     *
     * OW_PIN: GPIO pin number used for bit-banging 1-wire bus.
     * PWR_CTRL_PIN: power-control-GPIO pin number (optional).
     */
#ifdef PWR_CTRL_PIN
# if CONFIG_PWR_CTRL_ENABLED
#  error "CONFIG_PWR_CTRL_ENABLED needs to be configured"
# endif
    // switching transistor powering
    ow = new OneWireNg_CurrentPlatform(OW_PIN, PWR_CTRL_PIN);
#else
    // GPIO bit-bang powering
    ow = new OneWireNg_CurrentPlatform(OW_PIN);
#endif

    // ...

    // write array of bytes and power the bus subsequently;
    // the bus is powered until explicit unpowering or next 1-wire bus activity
    ow->writeBytes(bytes, bytes_len, true);

    // wait for connected slaves to fulfill their task requiring extra powering
    delay(750);

    // unpower the bus explicitly
    ow->powerBus(false);
}

configures 1-wire service to work in one of the above modes.

RP2040 PIO driver

RP2040 PIO driver (OneWireNg_PicoRP2040PIO class) doesn't support power-control-GPIO configuration. Since RP2040 platform is able to provide direct voltage source via its GPIO pads, parasitically powered devices need to be powered directly by GPIO controlling the 1-wire bus while using this driver.

Caveats

Parasite powered slaves are less stable (more error prone) than regularly powered devices. If possible, try to avoid parasitically powered setups.
For legacy AVR (non mega-AVR) and ESP8266 platforms (especially working in the parasitic mode) there are observed problems unless the parameter CONFIG_BUS_BLINK_PROTECTION is configured.

Architecture details

`OneWireNg`

The class provides public interface for 1-wire service. Object of this class isn't constructed directly rather than casted from a derived class object implementing platform specific details.

As an example:

#include "OneWireNg_CurrentPlatform.h"

static OneWireNg *ow = NULL;

void setup()
{
    OneWireNg::Id id;
    ow = new OneWireNg_CurrentPlatform(10);

    ow->searchReset();
    while (ow->search(id) == OneWireNg::EC_MORE) {
        // 'id' contains 1-wire address of a connected slave
    }
}

creates 1-wire service interface for current platform and performs search on the bus. The bus is controlled by MCU pin number 10. Alternatively it is possible to use C++11 range loop to detect slaves connected to the 1-wire bus:

#include "OneWireNg_CurrentPlatform.h"

static OneWireNg *ow = NULL;

void setup()
{
    ow = new OneWireNg_CurrentPlatform(10);

    for (const auto& id: *ow) {
        // 'id' contains 1-wire address of a connected slave
    }
}

NOTE: During creation of an OneWireNg object, the class constructor performs various platform specific activities required to setup the 1-wire service. For this reason the OneWireNg object may be created only when the platform itself is fully started-up and initialized, e.g. in setup() method but not as a global variable initialized during its creation.

Additionally it is strongly recommended to maintain single OneWireNg service object across all 1-wire activities handled by this service on a specific bus. Of course it is perfectly possible to created multiple OneWireNg services handling different 1-wire buses.

Memory allocation caveat

If heap allocation is inadvisable use in-place new operator:

#include "OneWireNg_CurrentPlatform.h"

ALLOC_ALIGNED static uint8_t OneWireNg_buf[sizeof(OneWireNg_CurrentPlatform)];
static OneWireNg *ow = NULL;

void setup()
{
    ow = new (OneWireNg_buf) OneWireNg_CurrentPlatform(10);
    // ...
}

or use Placeholder utility template to store OneWireNg specialized object:

#include "OneWireNg_CurrentPlatform.h"
#include "utils/Placeholder.h"

static Placeholder<OneWireNg_CurrentPlatform> ow;

void setup()
{
    // initialize the placeholded object by in-place new
    new (&ow) OneWireNg_CurrentPlatform(10);
    // ...
}

Refer to examples for more information how to use the Placeholder in the context of object stored within.

`OneWireNg_BitBang`

The class is derived from OneWireNg and implements the 1-wire interface basing on GPIO bit-banging. Object of this class isn't constructed directly rather than the class is intended to be inherited by a derived class providing protected interface implementation for low level GPIO activities (set mode, read, write).

`OneWireNg_PLATFORM`

Are family of classes providing platform specific implementation (PLATFORM states for a platform name e.g. OneWireNg_ArduinoAVR provides AVR implementation for Arduino environment).

The platform classes implement OneWireNg interface directly (via direct OneWireNg class inheritance) or indirectly (e.g. GPIO bit-banging implementation bases on OneWireNg_BitBang, which provides GPIO bit-banging 1-wire service implementation leaving the platform class to provide platform specific low-level GPIO activities details).

Platform classes have a public constructor allowing to create 1-wire service for a particular platform (see above).

NOTE: For the convenience there has been provided OneWireNg_CurrentPlatform.h header which tries to detect platform the compilation is proceeded and:

include proper platform class header,
assign OneWireNg_CurrentPlatform macro-define to the detected platform class.

RP2040 drivers

OneWireNg_PicoRP2040PIO is derived from OneWireNg and implements the 1-wire interface for RP2040 MCU using Programmable I/O (PIO) peripheral. Second type of driver supporting RP2040 platform is OneWireNg_PicoRP2040 bit-banging driver. Use CONFIG_RP2040_PIO_DRIVER configuration parameter to setup a specific driver for the platform.

NOTE: There are observed problems with Pico SDK's serial output (USB, UART) while using the bit-banging driver in TIMING_STRICT mode (see CONFIG_BITBANG_TIMING).

OneWire compatibility

OneWire class provides compatibility interface between OneWireNg and OneWire library. The main purpose of this class is to provide fast and effortless mechanism for developers experiencing issues with OneWire and eager to give OneWireNg a try. Finally, it's strongly recommended to switch into OneWireNg interface rather than stay with the OneWire due to OneWireNg's more mature and feature-rich API (search filtering, OD mode, touch support).

DallasTemperature library

As an example of usage of the compatibility interface there has been created the following fork of DallasTemperature library ported with OneWireNg.

License

2 clause BSD license. See LICENSE file for details.

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

README.md

README.md

OneWireNg

Table of Contents

Features

Usage

ESP-IDF (incl. ESP8266 RTOS SDK v3)

Pico SDK

Mbed OS

Supported platforms

Overdrive mode

Parasite powering

Architecture details

`OneWireNg`

Memory allocation caveat

`OneWireNg_BitBang`

`OneWireNg_PLATFORM`

RP2040 drivers

OneWire compatibility

DallasTemperature library

License

Files

README.md

Latest commit

History

README.md

File metadata and controls

OneWireNg

Table of Contents

Features

Usage

ESP-IDF (incl. ESP8266 RTOS SDK v3)

Pico SDK

Mbed OS

Supported platforms

Overdrive mode

Parasite powering

Architecture details

OneWireNg

Memory allocation caveat

OneWireNg_BitBang

OneWireNg_PLATFORM

RP2040 drivers

OneWire compatibility

DallasTemperature library

License

`OneWireNg`

`OneWireNg_BitBang`

`OneWireNg_PLATFORM`