-
Notifications
You must be signed in to change notification settings - Fork 0
/
taz.abs.fast.ini
131 lines (131 loc) · 3.67 KB
/
taz.abs.fast.ini
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
# generated by Slic3r 1.2.9 on Sat Jun 27 17:36:44 2015
avoid_crossing_perimeters = 0
bed_shape = 0x0,298x0,298x275,0x275
bed_temperature = 100
before_layer_gcode =
bottom_solid_layers = 2
bridge_acceleration = 1500
bridge_fan_speed = 0
bridge_flow_ratio = 1.01
bridge_speed = 40
brim_width = 10
complete_objects = 0
cooling = 1
default_acceleration = 1500
disable_fan_first_layers = 3
dont_support_bridges = 1
duplicate_distance = 6
end_gcode = M104 S0 ; turn off extruder temperature\nM140 S0 ; turn off bed\nM107 ; turn off Extruder Fans\nG28 X0 Y0 ; home X axis Y axis\n;M190 S40 ; wait for bed to be cool enough to remove part\n;M040 S0\nM109 S40 ; M190 releases if over set-point, use nozzle insted\nM104 S0\nG1 Y250 ; kick out bed\nM84 ; disable motors
external_fill_pattern = rectilinear
external_perimeter_extrusion_width = 0
external_perimeter_speed = 90
external_perimeters_first = 0
extra_perimeters = 1
extruder_clearance_height = 20
extruder_clearance_radius = 20
extruder_offset = 0x0
extrusion_axis = E
extrusion_multiplier = 1
extrusion_width = 0
fan_always_on = 0
fan_below_layer_time = 60
filament_colour = #FFFFFF
filament_diameter = 3
fill_angle = 45
fill_density = 20%
fill_pattern = rectilinear
first_layer_acceleration = 1000
first_layer_bed_temperature = 100
first_layer_extrusion_width = 200%
first_layer_height = 0.3
first_layer_speed = 65%
first_layer_temperature = 245
gap_fill_speed = 45
gcode_arcs = 0
gcode_comments = 0
gcode_flavor = reprap
infill_acceleration = 2000
infill_every_layers = 1
infill_extruder = 1
infill_extrusion_width = 0
infill_first = 0
infill_only_where_needed = 0
infill_overlap = 15%
infill_speed = 130
interface_shells = 0
layer_gcode =
layer_height = 0.25
max_fan_speed = 0
max_print_speed = 80
max_volumetric_speed = 0
min_fan_speed = 0
min_print_speed = 45
min_skirt_length = 0
notes =
nozzle_diameter = 0.4
octoprint_apikey =
octoprint_host =
only_retract_when_crossing_perimeters = 1
ooze_prevention = 0
output_filename_format = [input_filename_base].taz.abs.fast.gcode
overhangs = 0
perimeter_acceleration = 1050
perimeter_extruder = 1
perimeter_extrusion_width = 0
perimeter_speed = 115
perimeters = 4
post_process =
pressure_advance = 0
raft_layers = 0
resolution = 0.01
retract_before_travel = 2
retract_layer_change = 1
retract_length = 1.5
retract_length_toolchange = 10
retract_lift = 0
retract_restart_extra = 0
retract_restart_extra_toolchange = 0
retract_speed = 35
seam_position = aligned
skirt_distance = 6
skirt_height = 2
skirts = 2
slowdown_below_layer_time = 20
small_perimeter_speed = 75
solid_infill_below_area = 40
solid_infill_every_layers = 0
solid_infill_extruder = 1
solid_infill_extrusion_width = 0
solid_infill_speed = 115
spiral_vase = 0
standby_temperature_delta = -5
start_gcode = G28 ; home all axes\nM203 X150 Y150 Z3 ; Speed limits to minimize skipped steps when moving really fast courtesy of forum.lulzbot.com user 1013\nG1 Z10 ; heat up in the air or we melt the bed
support_material = 0
support_material_angle = 0
support_material_contact_distance = 0.2
support_material_enforce_layers = 0
support_material_extruder = 1
support_material_extrusion_width = 0
support_material_interface_extruder = 1
support_material_interface_layers = 3
support_material_interface_spacing = 0
support_material_interface_speed = 100%
support_material_pattern = pillars
support_material_spacing = 5
support_material_speed = 60
support_material_threshold = 0
temperature = 245
thin_walls = 1
threads = 2
toolchange_gcode =
top_infill_extrusion_width = 0
top_solid_infill_speed = 80
top_solid_layers = 5
travel_speed = 150
use_firmware_retraction = 0
use_relative_e_distances = 0
use_volumetric_e = 0
vibration_limit = 0
wipe = 0
xy_size_compensation = 0
z_offset = 0