conf.py

class conf():
    #mqtt server config - currently as simple as possible
    mqtt_addr          = '127.0.0.1'
    mqtt_port          = 1883
    mqtt_alive         = 60
    mqtt_status_topic  = "cc1101mqtt/status/"
    mqtt_rssi_topic    = "cc1101mqtt/rssi/"
    mqtt_command_topic = "cc1101mqtt/command/"


    spibus  = 0 # spidev for RPi, bus num for esp32
    spics   = 0 # and CS pin
    speed   = 5000000
    gdo0    = 24  # Pins using GPIO numbering for additional cc1101 signals
    gdo2    = 25

    # remotes/blinds config. 
    # Sniff the traffic to determine the 3 byte addresses and channel no.s of the blinds
    # the 3 byte address of each remote, you can have as many as you need
    remote_addr = [ [0xAA, 0xAA, 0xAA], [0xAA, 0xAA, 0xAA]  ]
    # for each remote above a list of 3 byte addresses and channel number for blinds
    # there can be 1-255(?) entries per remote but all should have the same numbers of entries
    # entries with 0x00s will be ignored
    remote_blind_id = [         
        #  <3 byte address>, <chl>  
        [ [0xAA, 0xAA, 0xAA, 0x00],
          [0xAA, 0xAA, 0xAA, 0x00],
          [0xAA, 0xAA, 0xAA, 0x00],
          [0xAA, 0xAA, 0xAA, 0x00],
          [0xAA, 0xAA, 0xAA, 0x00],
          [0xAA, 0xAA, 0xAA, 0x00],
          [0xAA, 0xAA, 0xAA, 0x00],
          [0xAA, 0xAA, 0xAA, 0x00],
          [0xAA, 0xAA, 0xAA, 0x00],
          [0xAA, 0xAA, 0xAA, 0x00],
          [0xAA, 0xAA, 0xAA, 0x00],
          [0xAA, 0xAA, 0xAA, 0x00],
          [0xAA, 0xAA, 0xAA, 0x00],
          [0x00, 0x00, 0x00, 0x00],
          [0x00, 0x00, 0x00, 0x00],
        ],
        [ [0x00, 0x00, 0x00, 0x00],
          [0x00, 0x00, 0x00, 0x00],
          [0x00, 0x00, 0x00, 0x00],
          [0x00, 0x00, 0x00, 0x00],
          [0x00, 0x00, 0x00, 0x00],
          [0x00, 0x00, 0x00, 0x00],
          [0x00, 0x00, 0x00, 0x00],
          [0x00, 0x00, 0x00, 0x00],
          [0x00, 0x00, 0x00, 0x00],
          [0x00, 0x00, 0x00, 0x00],
          [0x00, 0x00, 0x00, 0x00],
          [0x00, 0x00, 0x00, 0x00],
          [0x00, 0x00, 0x00, 0x00],
          [0x00, 0x00, 0x00, 0x00],
          [0x00, 0x00, 0x00, 0x00],
        ]
    ]

    retrans    = 3      # number of times to send each command >=1
    checkFreq  = 300    # check blind state every n seconds
    wdtTimeout = 400000 # esp32 only - in msec, the watchdog timeout > checkFreq time
    sleepTime  = 0.01   # seconds to sleep if no message received, RPi only, so we don't hog a cpu
    rawTrace   = False  # print all bytes sent/received in raw hex