forked from grblHAL/LPC176x
-
Notifications
You must be signed in to change notification settings - Fork 0
/
Copy pathmy_machine.h
62 lines (52 loc) · 2.99 KB
/
my_machine.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
/*
my_machine.h - configuration for NXP LPC176x ARM processors
Part of grblHAL
Copyright (c) 2020-2022 Terje Io
Grbl is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
Grbl is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with Grbl. If not, see <http://www.gnu.org/licenses/>.
*/
// NOTE: Only one board may be enabled!
// If none is enabled pin mappings from generic_map.h will be used
//#define SMOOTHIEBOARD
//#define BOARD_RAMPS_16
//#define BOARD_BTT_SKR_13
//#define BOARD_BTT_SKR_14_TURBO
//#define BOARD_BTT_SKR_E3_TURBO // With onboard Trinamic TNMC2209 drivers. NOTE: not verified!
//#define BOARD_MKS_SBASE_13
//#define BOARD_MY_MACHINE // Add my_machine_map.h before enabling this!
// Configuration
// Uncomment to enable, for some a value > 1 may be assigned, if so the default value is shown.
#ifndef USB_SERIAL_CDC
#define USB_SERIAL_CDC 1 // Comment out to use UART communication.
#endif
//#define SAFETY_DOOR_ENABLE 1 // Enable safety door input.
//#define SDCARD_ENABLE 1 // Run gcode programs from SD card, requires sdcard plugin.
//#define MPG_ENABLE 1 // Enable MPG interface. Requires serial port and one handshake pin.
//#define TRINAMIC_ENABLE 2130 // Uncomment to enable Trinamic TMC2130 driver support. NOTE: Experimental for now, currently for SKR 1.x boards only
//#define TRINAMIC_ENABLE 2209 // Uncomment to enable Trinamic TMC2209 driver support. NOTE: Experimental for now, currently for SKR 1.x boards only
//#define TRINAMIC_ENABLE 5160 // Uncomment to enable Trinamic TMC5160 driver support. NOTE: Experimental for now, currently for SKR E3 Turbo board only
//#define LIMIT_MAX_ENABLE 1 // Uncomment to enable max limit input pins (when available)
//#define EEPROM_ENABLE 1 // I2C EEPROM support. Set to 1 for 24LC16(2K), 2 (64 byte pages) or 3 (32 byte pages) for larger sizes. Requires eeprom plugin.
//#define EEPROM_IS_FRAM 1 // Uncomment when EEPROM is enabled and chip is FRAM, this to remove write delay.
// If the selected board map supports more than three motors ganging and/or auto-squaring
// of axes can be enabled here.
//#define X_GANGED 1
//#define X_AUTO_SQUARE 1
//#define Y_GANGED 1
//#define Y_AUTO_SQUARE 1
//#define Z_GANGED 1
//#define Z_AUTO_SQUARE 1
// For ganged axes the limit switch input (if available) can be configured to act as a max travel limit switch.
// NOTE: If board map already has max limit inputs defined this configuration will be ignored.
//#define X_GANGED_LIM_MAX 1
//#define Y_GANGED_LIM_MAX 1
//#define Z_GANGED_LIM_MAX 1
/*EOF*/