-
|
I'm new to njsPC so forgive me if I'm missing something obvious. I am trying to setup my heat pump with a fireman switch. I'm currently bench testing my unit. I have the fireman switch setup to a relay that is on GPIO27. GPIO27 is setup in REM and works when I click the button in REM. The heat pump is setup with the heater relay in dashPanel. However, I can't seem to get the heat pump to turn on. The logs have an error that says Any ideas? I'm on release 7.7, just installed it yesterday. Thanks for the help. For testing, if I put the heater as being a gas heater, the relay turn on/off as expected. Switching back to heat pump causes it to stop working and get the same errors about getTime.
|
Beta Was this translation helpful? Give feedback.
Replies: 5 comments 7 replies
-
|
Can I get you to produce a replay when you engage the heater and upload it here? Also which heat pump do you have? |
Beta Was this translation helpful? Give feedback.
-
|
I'm not sure what you mean by produce a replay, can you give some direction on that? I have a Hayward Heat Pump that only has the "2-wire" control for external controller. Not sure if you replied before my edit, but if I set the heater as a gas heater the relay works as expected. Right now I'm just doing some bench testing before actual install, so it isn't actually hooked up to the heater. I have ds18b20 probes providing the temperatures. |
Beta Was this translation helpful? Give feedback.
-
|
The instructions are here. https://github.com/tagyoureit/nodejs-poolController/wiki/How-to-capture-all-packets-for-issue-resolution |
Beta Was this translation helpful? Give feedback.
-
|
Man you guys made it easy to capture stuff. Attached is the replay. |
Beta Was this translation helpful? Give feedback.
-
|
Pull njsPC it should now work with a 2 wire heatpump hookup. |
Beta Was this translation helpful? Give feedback.
-
|
Its seems to be working now, except it says that it is cooling instead of heating. EDIT: It changed to heating. I restarted njsPC again it it starts off as showing cooling, but then switches over to colling after few seconds. |
Beta Was this translation helpful? Give feedback.
-
|
Pull njsPC. The cooling function needed to be disabled for 2-wire hookups on the heatpump. |
Beta Was this translation helpful? Give feedback.
-
|
Everything seems to be working now and the relay is probably triggering. Thanks for the support! |
Beta Was this translation helpful? Give feedback.
-
|
The heat pump is operating properly, but it doesn't seem to be trigging the "pool heater" circuit...so I can't seem to have my pump speed up when the heater is turned on. The "any heater" circuit turns on, but for whatever reason when I select that for the pump, it doesn't display any text or set the speed. |
Beta Was this translation helpful? Give feedback.
-
|
Hmm... Do you have solar? You shouldn't have a solar virtual circuit if there is no solar heater. I will take a look at your replay. |
Beta Was this translation helpful? Give feedback.
-
|
No solar. I do have a temp sensor on the output of my heater that is set as
watersensor2. I used it just to confirm heater operation.
…On Mon, May 30, 2022 at 9:23 PM rstrouse ***@***.***> wrote:
Hmm... Do you have solar? You shouldn't have a solar virtual circuit if
there is no solar heater. I will take a look at your replay.
—
Reply to this email directly, view it on GitHub
<#449 (reply in thread)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AB5EC6JHWRL545JL5WEJ7ALVMVSX3ANCNFSM5WKKRCNQ>
.
You are receiving this because you authored the thread.Message ID:
<tagyoureit/nodejs-poolController/repo-discussions/449/comments/2852159@
github.com>
|
Beta Was this translation helpful? Give feedback.
-
|
Pull njsPC the heatpump states were not included in the heater virtual circuits. |
Beta Was this translation helpful? Give feedback.
Pull njsPC. The cooling function needed to be disabled for 2-wire hookups on the heatpump.