Intelliflo Pump Settings? #755
Replies: 12 comments 10 replies
-
This should work. There could be some corruption in your data files. Can you upload a replay here? Also, if you enable the javascript console you may see an error in the logs. |
Beta Was this translation helpful? Give feedback.
-
I got it fixed. I reloaded the config and now it works properly. Thanks |
Beta Was this translation helpful? Give feedback.
-
I spoke too soon. I was working on some rule machine rules for my hubitat dashboard today when the nodejs-dash reverted back to the same behavior. What do you recommend? Any chance there's logs showing what happened when it auto reverted? If so, where would they be? |
Beta Was this translation helpful? Give feedback.
-
There is not but perhaps we may see something from a replay. Specifically how the data is corrupted. |
Beta Was this translation helpful? Give feedback.
-
Is there an easy way to nuke everything and start over? I have everything running at startup with pm2, so after running 'pm2 unstartup' and pasting the output, do i just uninstall/reinstall npm to start over? |
Beta Was this translation helpful? Give feedback.
-
I've also noticed the errant 31,XXX RPM # assigned to circuits before but hasn't happened in a week or so. Even now, my rpm settings page is showing the incorrect rpms for the SPA (supposed to be 2860, not 450). It does actually run at 2860, so that's good. And my lights don't have an rpm assigned to the circuit 🤷♂️: RPM settings tab from screen logic: Happy to provide a replay, just let me know what you want me to capture. Oh, and I'm not running the hubitat integration like @dcorrea78 but I do have an easytouch-4 |
Beta Was this translation helpful? Give feedback.
-
So my issue has got worse. So after the pump started showing the SPA circuit twice, I could no longer change pump speeds and got an InvalidEquipmentData errror. So I decided to just nuke the whole thing and start over with a clean install. Unfortunately it is doing the same thing. I can go into the settings and change the circuit back to the pool circuit, but it changes back after a few minutes. So at this point, changing the pump RPM is broken for me.
|
Beta Was this translation helpful? Give feedback.
-
Ok so I found the replay that was sandwiched in between the two screenshots. Sucker was hiding from me. From this I determined that ScreenLogic asks for the configuration from the old IntelliFlo4 and in a ridiculous twist EasyTouch returns garbage. We were seeing this garbage and picked it up as gospel without first checking the firmware version. We assumed it would never show up if it were not correct. Anyway pull njsPC then please do a replay that includes reloading the config. |
Beta Was this translation helpful? Give feedback.
-
I think you are asking me for an updated replay. I can do that in a few hours when I get home. Forgive my ignorance, but when you say pull njsPC, are you saying to do a git pull to update njsPC?
Get Outlook for Android<https://aka.ms/AAb9ysg>
…________________________________
From: rstrouse ***@***.***>
Sent: Saturday, May 13, 2023, 1:07 PM
To: tagyoureit/nodejs-poolController ***@***.***>
Cc: dcorrea78 ***@***.***>; Mention ***@***.***>
Subject: Re: [tagyoureit/nodejs-poolController] Intelliflo Pump Settings? (Discussion #755)
Ok so I found the replay that was sandwiched in between the two screenshots. Sucker was hiding from me. From this I determined that ScreenLogic asks for the configuration from the old IntelliFlo4 and in a ridiculous twist EasyTouch returns garbage. We were seeing this garbage and picked it up as gospel without first checking the firmware version. We assumed it would never show up if it were not correct.
Anyway pull njsPC then please do a replay that includes reloading the config.
—
Reply to this email directly, view it on GitHub<#755 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/AIGWRJMJPKSZPOYL3IMJX5LXF65WFANCNFSM6AAAAAAXZE3SVM>.
You are receiving this because you were mentioned.Message ID: ***@***.***>
|
Beta Was this translation helpful? Give feedback.
-
I'll attach my results. I think I'm good now. Pump config page is showing correct rpm circuits: Not sure I took the right route to git here but I'll post in case you have any comments. Did a git pull/npm i. Then started a replace with config reloaded. The config came up completely empty, as if I had a new nixie install with nothing configured, instead of my previously configured ET4 config: replay of the reload config here: I didn't like the look of that so I started a second replay and did a full stack pm2 restart. This time, my ET4 config reloaded and my pump config page looked good. Just had to hide an AUX circuit that shouldn't have been showing and I was back in business. 2nd replay here: bottom line, I think I'm good? Unless you see something in the replay you don't like. Thanks for looking at this. Hope this works for @dcorrea78 as well. |
Beta Was this translation helpful? Give feedback.
-
Here's my replay. I also had to do a pm2 restart to get the config to reload properly. |
Beta Was this translation helpful? Give feedback.
-
I went all day today with no issues. Looks like everything is fixed. Thank you! |
Beta Was this translation helpful? Give feedback.
-
I have nodejs-poolController and the nodejs-poolController-dashPanel installed and running successfully on a RPi4. My system has a *touch 2-8 to control a spa and pool, and my pump is a Intelliflo VSF pump. When using the dashboard, the pump settings show the wrong circuits, and I cannot manually change circuit or change the pump speed. I have tried to add the correct pool circuit, but whenever I update the pump it just spins and never updates. Is there a way to manually set the pump speed and update the pump circuits? What am I doing wrong?
Beta Was this translation helpful? Give feedback.
All reactions