Final

Mk2_3phase_RFdatalog_temp/calibration.h

@@ -31,7 +31,7 @@
 // powerCal is the RECIPROCAL of the power conversion rate. A good value
 // to start with is therefore 1/20 = 0.05 (Watts per ADC-step squared)
 //
-inline constexpr float f_powerCal[NO_OF_PHASES]{ 0.05000F, 0.05000F, 0.05000F };
+inline constexpr float f_powerCal[NO_OF_PHASES]{ 0.043950F, 0.045235F, 0.042788F };
 //
 // f_phaseCal is used to alter the phase of the voltage waveform relative to the current waveform.
 // The algorithm interpolates between the most recent pair of voltage samples according to the value of f_phaseCal.

Mk2_3phase_RFdatalog_temp/config.h

@@ -35,7 +35,7 @@
 //--------------------------------------------------------------------------------------------------
 // constants which must be set individually for each system
 //
-inline constexpr uint8_t NO_OF_DUMPLOADS{ 2 }; /**< number of dump loads connected to the diverter */
+inline constexpr uint8_t NO_OF_DUMPLOADS{ 3 }; /**< number of dump loads connected to the diverter */
 
 #ifdef EMONESP
 inline constexpr bool EMONESP_CONTROL{ true };
@@ -50,7 +50,7 @@ inline constexpr bool OVERRIDE_PIN_PRESENT{ false };                    /**< set
 #endif
 
 inline constexpr bool WATCHDOG_PIN_PRESENT{ false }; /**< set it to 'true' if there's a watch led */
-inline constexpr bool RELAY_DIVERSION{ false };       /**< set it to 'true' if a relay is used for diversion */
+inline constexpr bool RELAY_DIVERSION{ false };      /**< set it to 'true' if a relay is used for diversion */
 inline constexpr bool DUAL_TARIFF{ false };          /**< set it to 'true' if there's a dual tariff each day AND the router is connected to the billing meter */
 
 // ----------- Pinout assignments -----------
@@ -71,8 +71,8 @@ inline constexpr bool DUAL_TARIFF{ false };          /**< set it to 'true' if th
 // D12 is MISO
 // D13 is SCK
 
-inline constexpr uint8_t physicalLoadPin[NO_OF_DUMPLOADS]{ 5, 7 };         /**< for 3-phase PCB, Load #1/#2/#3 (Rev 2 PCB) */
-inline constexpr uint8_t loadPrioritiesAtStartup[NO_OF_DUMPLOADS]{ 0, 1 }; /**< load priorities and states at startup */
+inline constexpr uint8_t physicalLoadPin[NO_OF_DUMPLOADS]{ 5, 6, 7 };         /**< for 3-phase PCB, Load #1/#2/#3 (Rev 2 PCB) */
+inline constexpr uint8_t loadPrioritiesAtStartup[NO_OF_DUMPLOADS]{ 0, 1, 2 }; /**< load priorities and states at startup */
 
 // Set the value to 0xff when the pin is not needed (feature deactivated)
 inline constexpr uint8_t dualTariffPin{ 0xff }; /**< for 3-phase PCB, off-peak trigger */

Mk2_3phase_RFdatalog_temp/config_system.h

@@ -20,7 +20,7 @@ inline constexpr uint8_t NO_OF_PHASES{ 3 }; /**< number of phases of the main su
 
 //--------------------------------------------------------------------------------------------------
 // for users with zero-export profile, this value will be negative
-inline constexpr int16_t REQUIRED_EXPORT_IN_WATTS{ 20 }; /**< when set to a negative value, this acts as a PV generator */
+inline constexpr int16_t REQUIRED_EXPORT_IN_WATTS{ 0 }; /**< when set to a negative value, this acts as a PV generator */
 
 //--------------------------------------------------------------------------------------------------
 // other system constants, should match most of installations

Mk2_3phase_RFdatalog_temp/processing.cpp

@@ -59,7 +59,7 @@ float f_upperEnergyThreshold;        /**< dynamic upper threshold */
 // for improved control of multiple loads
 bool b_recentTransition{ false };                 /**< a load state has been recently toggled */
 uint8_t postTransitionCount;                      /**< counts the number of cycle since last transition */
-constexpr uint8_t POST_TRANSITION_MAX_COUNT{ 3 }; /**< allows each transition to take effect */
+constexpr uint8_t POST_TRANSITION_MAX_COUNT{ 2 }; /**< allows each transition to take effect */
 // constexpr uint8_t POST_TRANSITION_MAX_COUNT{50}; /**< for testing only */
 uint8_t activeLoad{ NO_OF_DUMPLOADS }; /**< current active load */
 

dev/cal_CTx_v_meter/main.cpp

@@ -127,7 +127,7 @@ constexpr int16_t ADCDuration{ 104 };  // Time in microseconds for one ADC conve
 // powerCal is the RECIPR0CAL of the power conversion rate. A good value
 // to start with is therefore 1/20 = 0.05 (Watts per ADC-step squared)
 //
-inline constexpr float f_powerCal[NO_OF_PHASES]{ 0.050000F, 0.050000F, 0.050000F };
+inline constexpr float f_powerCal[NO_OF_PHASES]{ 0.043950F, 0.045235F, 0.042788F };
 
 // f_phaseCal is used to alter the phase of the voltage waveform relative to the
 // current waveform. The algorithm interpolates between the most recent pair