0.2.1-beta

修改readme，将loop中，显示数据，以及各个传感器的监测时间轴分开，CDK

ESP8266_GreenBox/GreenBox.0.2.0-beta/GreenBox.0.2.0-beta.ino

@@ -1,6 +1,6 @@
 #include "GreenBox_Define.h"
 #include "GreenBox_Function.h"
-// https://blog.csdn.net/tongyue/article/details/105305280
+
 void setup() {
   // put your setup code here, to run once:
   // ESP8266 initialization

ESP8266_GreenBox/GreenBox.0.2.1-beta/GreenBox.0.2.1-beta.ino

@@ -0,0 +1,10 @@
+#include "GreenBox_Define.h"
+#include "GreenBox_Function.h"
+void setup() {
+  setup_function();
+  delay(2000); // the time used to setup
+}
+void loop() {
+  loop_function();
+  delay(500); // 500 milliseconds as a unit of time measurement
+}

ESP8266_GreenBox/GreenBox.0.2.1-beta/GreenBox_Define.h

@@ -0,0 +1,120 @@
+///////////////////////////////////////////////////////// Headers /////////////////////////////////////////////////////////
+#include <Wire.h>
+#include <LiquidCrystal_I2C.h>
+#include <DFRobot_VEML7700.h>
+#include <Servo.h>
+#include <Adafruit_NeoPixel.h>
+#include <DFRobot_INA219.h>
+#include <ESP8266WiFi.h>
+
+/////////////////////////////////////////////////////// WiFi ///////////////////////////////////////////////////////
+IPAddress staticIP(192, 168, 100, 100);  // esp8266开发板的固定IP地址
+IPAddress gateway(192, 168, 100, 1);  // 网关地址，路由器的IP地址
+IPAddress subnet(255, 255, 255, 0);  // 子网掩码
+IPAddress dns(192, 168, 100, 1);  // dns服务器默认
+
+//HTTPClient http;
+
+/////////////////////////////////////////////////////// Hardwares ///////////////////////////////////////////////////////
+// detectors
+// Temp & humidity
+#define Addr_SHT30 0x44   // SHT30 IIC 7-bit address is 0x44
+// LIGHT
+DFRobot_VEML7700 VEML7700;   // address is 0x10
+// WATER
+#define PIN_WATER A0
+// CO2
+#define CO2_SENSOR_DATA_PIN   (12)   // GPIO 12 (D6) Sensor PWM interface
+#define INTERRUPT_NUMBER   digitalPinToInterrupt(CO2_SENSOR_DATA_PIN)   // interrupt number
+// Wattmeter
+//DFRobot_INA219_IIC     wattmeter_ina219(&Wire, INA219_I2C_ADDRESS3); // address3 是0x44 与SHT30 设置的重复了
+DFRobot_INA219_IIC     wattmeter_ina219_fan(&Wire, INA219_I2C_ADDRESS1);
+DFRobot_INA219_IIC     wattmeter_ina219_RGB_LED(&Wire, INA219_I2C_ADDRESS2);
+DFRobot_INA219_IIC     wattmeter_ina219_semiconductor_cooling(&Wire, INA219_I2C_ADDRESS4);
+
+
+// The output hardwares's DEFINE (WIND & LIGHT)
+// LCD1602
+LiquidCrystal_I2C LCD1602(0x27,16,2); // Set the address of the LCD1602: 0x27
+// LED_WS2812
+#define PIN_LED_RGB 14 // GPIO 14 (D5)
+#define LED_RGB_NUMPIXELS 145 // 彩灯个数
+Adafruit_NeoPixel LED_RGB(LED_RGB_NUMPIXELS, PIN_LED_RGB, NEO_GRB + NEO_KHZ800);
+// SG90_WIND
+#define PIN_SG90_WIND 13  // GPIO 13 (D7)
+Servo SG90_WIND;
+
+//////////////////////////////////////////////////////////// Datas ////////////////////////////////////////////////////////////
+// The data from sensors (Global)
+// sht30
+unsigned int sht30_data[6]; //store the six acquired data of sht30 for temp and humidity
+float sht30_cTemp = 0.0;
+float sht30_fTemp = 0.0;
+float sht30_humidity = 0.0;
+// water depth
+float water_depth = 0.0;
+// Lightness
+float VEML7700_light = 0.0;
+// CO2
+float CO2_pwm_high_val_ms = 0.0;
+float CO2_concentration = 0.0;
+volatile unsigned long CO2_pwm_high_start_ticks=0, CO2_pwm_high_end_ticks=0;// Used in interrupt, calculate pulse width variable
+volatile unsigned long CO2_pwm_high_val=0, CO2_pwm_low_val=0;
+volatile uint8_t CO2_flag=0;// interrupt flag
+// Wattmeter 功率计
+// Wattmeter 是否连接 flag, 0 表示未连接该 Wattmeter
+int wattmeter_flag_fan = 0; 
+int wattmeter_flag_RGB_LED = 0;
+int wattmeter_flag_semiconductor_cooling = 0;
+// Wattmeter 功率计校准
+float ina219Reading_mA_fan = 1000; //Modify the variable in the code according to the current value printed by the serial port
+float extMeterReading_mA_fan = 1000; //Modify the variables in the code according to the current value of the multimeter
+float ina219Reading_mA_RGB_LED = 1000; //Modify the variable in the code according to the current value printed by the serial port
+float extMeterReading_mA_RGB_LED = 1000; //Modify the variables in the code according to the current value of the multimeter
+float ina219Reading_mA_semiconductor_cooling = 1000; //Modify the variable in the code according to the current value printed by the serial port, 实际超量程，建议换电流计
+float extMeterReading_mA_semiconductor_cooling = 1000; //Modify the variables in the code according to the current value of the multimeter
+// Wattmeter 示数 fan
+float BusVoltage_fan = 0.0;
+float ShuntVoltage_fan = 0.0;
+float current_fan = 0.0;
+float power_fan = 0.0;
+// Wattmeter 示数 RGB_LED
+float BusVoltage_RGB_LED = 0.0;
+float ShuntVoltage_RGB_LED = 0.0;
+float current_RGB_LED = 0.0;
+float power_RGB_LED = 0.0;
+// Wattmeter 示数 semiconductor_cooling
+float BusVoltage_semiconductor_cooling = 0.0;
+float ShuntVoltage_semiconductor_cooling = 0.0;
+float current_semiconductor_cooling = 0.0;
+float power_semiconductor_cooling = 0.0;
+
+
+///////////////////////////////////////////////////// Variables for controlled Output /////////////////////////////////////////////////////
+// The variables for controlled output values, such as the speed of the wind (Global)
+// Wind
+int wind_force = 180;
+// LIGHT
+int LED_R = 255;
+int LED_G = 42;
+int LED_B = 170;
+int LED_RGB_Brightness = 120;
+int LED_kapa = 0; //用于循环的一个个为LED赋值，for loop
+
+///////////////////////////////////////////////////// Variables for networks /////////////////////////////////////////////////////
+String Year_esp8266 = "";
+String Date_esp8266 = "";
+String Time_esp8266 = "";
+
+///////////////////////////////////////////////////// Variables for the loop /////////////////////////////////////////////////////
+// 通过数时间的方式来让不同的元件以不同的时间间隔, 删除大部分函数中的delay() function
+// 设计结构：不同传感器有不同的监测周期，LCD的显示也独立于监测，还有数据的向云端上传
+// 最小的时间间隔：500ms
+int count_sht30 = 0; // 1000ms 监测一次
+int count_water = 0; // 5000ms 监测一次
+int count_light = 0; // 1000ms 监测一次
+int count_CO2 = 0; // 1000ms 监测一次
+int count_wattmeter = 0; // 1000ms 监测一次
+int count_wind = 0; // 60000ms = 1min 更改一次
+int count_led = 0; // 5000ms 更改一次
+int count_lcd = 0; // 根据显示的需求可以调整