ESP-IDF failure

[Bakermakes]

I'm trying to flash my ESP32 and no matter what I try, I keep getting this error, screenshot attached

. Are you able to shed any light as to what's happening?

[mawoka-myblock]

You have to have git installed

[Bakermakes]

That didn't make much of a difference. If I may provide some feedback, I would either remove the "build from scratch" option on your readme until you have thorough documentation on how to flash the esp32 or make it very abundantly clear that this is not a project that someone with limited experience can accomplish. I am finding myself very frustrated with this process and the lack of any guides is making it difficult to proceed. Just my two cents. I will bang my head against a wall until I get this, but many others will not

…

On Wed, Nov 6, 2024, 12:21 AM Marlon ***@***.***> wrote: You have to have git installed — Reply to this email directly, view it on GitHub <#4 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/BMOGLCBCMXJLSYNNOTAR4OTZ7GRO5AVCNFSM6AAAAABRH3542SVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTCMJWGI2DENI> . You are receiving this because you authored the thread.Message ID: ***@***.***>

[mawoka-myblock]

I understand your frustration, but I'd like to point out that I'm not keen on providing a 1-to-1 assistance on how to get the esp-rs setup working. If the documentation is lacking in this regard, feel free to tell the folks over in their repo, but that's not really my business. Follow the following instructions: https://docs.esp-rs.org/book/installation/index.html. They'll guide you thorugh the process of installing Rust for the ESP32 C3 including the std library. Again, I understand your situation though I honestly don't see myself at fault. Adding a sentence on where exactly the docs can be found would be a good idea, for sure, but that doesn't seem t be your problem right here as you're further than that.

[Bakermakes]

Thank you for that link. I agree that adding that sentence to the readme would be helpful. I understand you are not keen on helping with installation on a 1-to-1 basis, which is why I recommended removing the section about making it from scratch. If I had known that it would be so frustrating trying to get this to work, I would have just gone straight to ordering the assembled piece from you. You may be able to drive sales by not encouraging others to try and replicate what you have done. As I have already purchased the individual pieces and have physically built the unit, this is the bed I now have to sleep in. I made my recommendation in order for you to hopefully avoid more people like me having similar issues.

…

On Wed, Nov 6, 2024 at 4:18 PM Marlon ***@***.***> wrote: I understand your frustration, but I'd like to point out that I'm not keen on providing a 1-to-1 assistance on how to get the esp-rs setup working. If the documentation is lacking in this regard, feel free to tell the folks over in their repo, but that's not really my business. Follow the following instructions: https://docs.esp-rs.org/book/installation/index.html. They'll guide you thorugh the process of installing Rust for the *ESP32 C3* including the *std* library. Again, I understand your situation though I honestly don't see myself at fault. Adding a sentence on where exactly the docs can be found would be a good idea, for sure, but that doesn't seem t be your problem right here as you're further than that. — Reply to this email directly, view it on GitHub <#4 (reply in thread)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/BMOGLCB26RRFCD63KAJ2UIDZ7KBRJAVCNFSM6AAAAABRH3542SVHI2DSMVQWIX3LMV43URDJONRXK43TNFXW4Q3PNVWWK3TUHMYTCMJXGA4TSOA> . You are receiving this because you authored the thread.Message ID: ***@***.***>