-
Notifications
You must be signed in to change notification settings - Fork 4
Changelogs
noone2k edited this page Oct 11, 2024
·
11 revisions
FW | Notes | Type | Released |
---|---|---|---|
123 | Auslieferungsversion - 1st Batch | Release | |
124 | Auslieferungsversion - 2nd Batch | Release | |
131 | Only upgrade with independent boot between v131 and v132 | Release | |
132¹ | Only for v123 version upgrade ( Batch 1 - Bootloader ) | Release | |
132¹ | v124 or above upgraded version ( Batch 2 ) | Release | |
135 | New certificate, 0 degree pass-through | Release | 18.3.2024 |
137 | Switch delay | Release | 23.04.2024 |
138 | Parallel communication ( MQTT ) | Release | 13.05.2024 |
139 | Optimize discharge lithium protection | Beta | 07.06.2024 |
140² | Push carefully to eliminate the short circuit | Beta | 12.06.2024 |
141.5 | Parallel machine (MQTT) loss optimization, data upload | Beta | 23.08.2024 |
141.7³ | Based on 141.5 with short circuit protection turned off. | Beta | 23.08.2024 |
141.11 | Optimized transparent transmission to discharge for 6 minutes, compatible with Deye relay | Release | 05.09.2024 |
¹ Die 132 gibt es in zwei Ausführungungen. Einmal von der 1.23 und von 124 ( Charge 1 und 2 - Bootloader dependant ? ) ² Bei der 140 kann es vorkommen, das es zu einem Bootloop kommt. Dieser verschwindet, sobald man wieder Power zuführt. ³ Fehler im "Verteilersystem" von Hametech ... aktuell kann diese nicht eingespielt werden. ( Space in Filename )
FW | Notes | Type | Released |
---|---|---|---|
119 | Auslieferungsversion 2nd Generation | Release | |
157 | New certificate, 0 degree pass-through | Release | 20.03.2024 |
160 | Parallel communication ( MQTT ) | Release | 30.04.2024 |
163 | Charge and discharge at the same time | Release | 09.05.2024 |
200.1 | Temporary-cancel low current restart | Release | 30.05.2024 |
208 | New certificate, 0 degree pass-through | Release | 16.04.2024 |
210.26 | New parallel machine ( MQTT ) and cancellation of small current | Release | 04.06.2024 |
211.1 | Temporary minor version 6.4 | Beta | |
212.18 | Optimize NEP | Release | 27.06.2024 |
214.2 | Return to pass-through | Release | 09.07.2024 |
215.1 | Testing AP Micro-inverter | Beta | 16.07.2024 |
215.3 | Parallel connection ( MQTT ) is lost, restart to search | Beta | 19.07.2024 |
215.4 | beta | beta | 08.08.2024 |
200.5 | Test package cutting failure for customers | Beta | 08.08.2024 |
215.5 | Test CT for customers using microinverters with rated power other than 800W | Beta | 15.08.2024 |
216.17 | Forced charging, CT search, AP compatibility | Release | 16.08.2024 |
217.21 | Packets cannot be cut when fully charged. Determine the dod before searching for the CT channel. | Beta | 21.08.2024 |
217.22 | 1. When all packages are fully charged, package cutting is not allowed. - 2. Before searching for the CT channel, if the current packet undervoltage or dod situation occurs, the CT channel cannot be searched for; there are two ways to relieve it: a. Exit the CT mode.b. Charge the device input until the dod is released. - 3. Use mqtt high-frequency access to modify the correct channel voltage value. | Beta | 28.08.2024 |
217.23 | Eliminate secondary overcharge protection detection | Beta | 03.09.2024 |
217.24 | Solved the problem that the output power is lower than the setting according to customer feedback | Beta | 04.09.2024 |
217.25 | Set single-channel output when power is less than half of the rated power of the micro-inverter | Beta | 06.09.2024 |
218.7 | 1. Change the output backflow judgment voltage from 16V to 30V 2. Increase the time period to 5 segments 3. Support OTA upgrade with power supply package | Release | 11.10.2024 |