#563 #589 Small perimeter control

resources/ui_layout/print.ui

@@ -192,7 +192,6 @@ group:label_width$8:Speed for print moves
 	line:Perimeter speed
 		setting:width$4:perimeter_speed
 		setting:width$4:external_perimeter_speed
-		setting:width$4:small_perimeter_speed
 	end_line
 	line:Infill speed
 		setting:width$4:infill_speed
@@ -217,6 +216,10 @@ group:Modifiers
 		setting:label_width$8:width$4:first_layer_speed
 		setting:label_width$8:width$4:first_layer_infill_speed
 	end_line
+	line:Small perimeter speed
+		setting:label_width$8:width$4:small_perimeter_min_length
+		setting:label_width$8:width$4:small_perimeter_max_length
+		setting:label_width$8:width$4:small_perimeter_speed
 group:Acceleration control (advanced)
 	setting:perimeter_acceleration
 	setting:infill_acceleration

src/libslic3r/GCode.cpp

@@ -3034,8 +3034,16 @@ std::string GCode::extrude_loop_vase(const ExtrusionLoop &original_loop, const s
     if (paths.empty()) return "";
 
     // apply the small/external? perimeter speed
-    if (is_perimeter(paths.front().role()) && loop.length() <= SMALL_PERIMETER_LENGTH && speed == -1)
-        speed = m_config.external_perimeter_speed.get_abs_value(m_config.perimeter_speed);
+    if (speed == -1 && is_perimeter(paths.front().role()) && loop.length() <=
+        scale_(this->m_config.small_perimeter_max_length.get_abs_value(EXTRUDER_CONFIG_WITH_DEFAULT(nozzle_diameter, 0)))) {
+        double min_length = scale_(this->m_config.small_perimeter_min_length.get_abs_value(EXTRUDER_CONFIG_WITH_DEFAULT(nozzle_diameter, 0)));
+        double max_length = scale_(this->m_config.small_perimeter_max_length.get_abs_value(EXTRUDER_CONFIG_WITH_DEFAULT(nozzle_diameter, 0)));
+        if (loop.length() <= min_length) {
+            speed = m_config.small_perimeter_speed.get_abs_value(m_config.perimeter_speed);
+        } else {
+            speed = - (loop.length() - min_length) / (max_length - min_length);
+        }
+    }
 
     //get extrusion length
     coordf_t length = 0;
@@ -3552,8 +3560,16 @@ std::string GCode::extrude_loop(const ExtrusionLoop &original_loop, const std::s
     if (paths.empty()) return "";
 
     // apply the small perimeter speed
-    if (is_perimeter(paths.front().role()) && loop.length() <= SMALL_PERIMETER_LENGTH && speed == -1)
-        speed = m_config.small_perimeter_speed.get_abs_value(m_config.perimeter_speed);
+    if (speed == -1 && is_perimeter(paths.front().role()) && loop.length() <=
+        scale_(this->m_config.small_perimeter_max_length.get_abs_value(EXTRUDER_CONFIG_WITH_DEFAULT(nozzle_diameter, 0)))) {
+        double min_length = scale_(this->m_config.small_perimeter_min_length.get_abs_value(EXTRUDER_CONFIG_WITH_DEFAULT(nozzle_diameter, 0)));
+        double max_length = scale_(this->m_config.small_perimeter_max_length.get_abs_value(EXTRUDER_CONFIG_WITH_DEFAULT(nozzle_diameter, 0)));
+        if (loop.length() <= min_length) {
+            speed = m_config.small_perimeter_speed.get_abs_value(m_config.perimeter_speed);
+        } else {
+            speed = -(loop.length() - min_length) / (max_length - min_length);
+        }
+    }
 
     // extrude along the path
     std::string gcode;
@@ -4130,7 +4146,10 @@ std::string GCode::_before_extrude(const ExtrusionPath &path, const std::string
 
 
     // set speed
-    if (speed == -1) {
+    if (speed < 0) {
+        //if speed == -1, then it's means "choose yourself, but if it's -1 < speed <0 , then it's a scaling from small_periemter.
+        //it's a bit hacky, so if you want to rework it, help yourself.
+        float factor = (-speed);
         if (path.role() == erPerimeter) {
             speed = m_config.get_abs_value("perimeter_speed");
         } else if (path.role() == erExternalPerimeter) {
@@ -4154,6 +4173,12 @@ std::string GCode::_before_extrude(const ExtrusionPath &path, const std::string
         } else {
             throw std::invalid_argument("Invalid speed");
         }
+        //don't modify bridge speed
+        if (factor < 1 && !(path.role() == erOverhangPerimeter || path.role() == erBridgeInfill)) {
+            float small_speed = m_config.small_perimeter_speed.get_abs_value(m_config.perimeter_speed);
+            //apply factor between feature speed and small speed
+            speed = speed * factor + (1 - factor) * small_speed;
+        }
     }
     if (m_volumetric_speed != 0. && speed == 0)
         speed = m_volumetric_speed / path.mm3_per_mm;

src/libslic3r/Layer.cpp

@@ -163,6 +163,8 @@ void Layer::make_perimeters()
                 && config.perimeter_overlap         == other_config.perimeter_overlap
                 && config.perimeter_speed           == other_config.perimeter_speed // it os mandatory? can't this be set at gcode.cpp?
                 && config.small_perimeter_speed     == other_config.small_perimeter_speed
+                && config.small_perimeter_min_length == other_config.small_perimeter_min_length
+                && config.small_perimeter_max_length == other_config.small_perimeter_max_length
                 && config.thin_walls                == other_config.thin_walls
                 && config.thin_walls_min_width      == other_config.thin_walls_min_width
                 && config.thin_walls_overlap        == other_config.thin_walls_overlap

src/libslic3r/PrintConfig.cpp

@@ -2838,18 +2838,44 @@ void PrintConfigDef::init_fff_params()
     def->set_default_value(new ConfigOptionInts{ 5 });
 
     def = this->add("small_perimeter_speed", coFloatOrPercent);
-    def->label = L("Small");
+    def->label = L("Speed");
     def->full_label = ("Small perimeters speed");
     def->category = OptionCategory::speed;
     def->tooltip = L("This separate setting will affect the speed of perimeters having radius <= 6.5mm "
-                   "(usually holes). If expressed as percentage (for example: 80%) it will be calculated "
-                   "on the perimeters speed setting above. Set to zero for auto.");
+        "(usually holes). If expressed as percentage (for example: 80%) it will be calculated "
+        "on the perimeters speed setting above. Set to zero for auto.");
     def->sidetext = L("mm/s or %");
     def->ratio_over = "perimeter_speed";
     def->min = 0;
     def->mode = comAdvanced;
     def->set_default_value(new ConfigOptionFloatOrPercent(15, false));
 
+    def = this->add("small_perimeter_min_length", coFloatOrPercent);
+    def->label = L("Min length");
+    def->full_label = ("Min small perimeters length");
+    def->category = OptionCategory::speed;
+    def->tooltip = L("This set the threshold for small periemter length. Every loop with a length lower than that will be printed at small perimeter speed"
+        "\nCan be a mm or a % of the nozzle diameter.");
+    def->sidetext = L("mm or %");
+    def->ratio_over = "nozzle_diameter";
+    def->min = 0;
+    def->mode = comAdvanced;
+    def->set_default_value(new ConfigOptionFloatOrPercent(6, false));
+
+
+    def = this->add("small_perimeter_max_length", coFloatOrPercent);
+    def->label = L("Max length");
+    def->full_label = ("Max small perimeters length");
+    def->category = OptionCategory::speed;
+    def->tooltip = L("This set the end of the threshold for small periemter length."
+        " Every periemter loop lower than that will see their speed reduced a bit, from their normal spee at this length down to small perimeter speed."
+        "\nCan be a mm or a % of the nozzle diameter.");
+    def->sidetext = L("mm or %");
+    def->ratio_over = "nozzle_diameter";
+    def->min = 0;
+    def->mode = comAdvanced;
+    def->set_default_value(new ConfigOptionFloatOrPercent(20, false));
+
     def = this->add("curve_smoothing_angle_convex", coFloat);
     def->label = L("Min convex angle");
     def->full_label = L("Curve smoothing minimum angle (convex)");

src/libslic3r/PrintConfig.hpp

@@ -711,6 +711,8 @@ class PrintRegionConfig : public StaticPrintConfig
     ConfigOptionPercent             print_extrusion_multiplier;
     ConfigOptionFloat               print_retract_length;
     ConfigOptionFloatOrPercent      small_perimeter_speed;
+    ConfigOptionFloatOrPercent      small_perimeter_min_length;
+    ConfigOptionFloatOrPercent      small_perimeter_max_length;
     ConfigOptionEnum<InfillPattern> solid_fill_pattern;
     ConfigOptionFloat               solid_infill_below_area;
     ConfigOptionInt                 solid_infill_extruder;
@@ -802,6 +804,8 @@ class PrintRegionConfig : public StaticPrintConfig
         OPT_PTR(print_extrusion_multiplier);
         OPT_PTR(print_retract_length);
         OPT_PTR(small_perimeter_speed);
+        OPT_PTR(small_perimeter_min_length);
+        OPT_PTR(small_perimeter_max_length);
         OPT_PTR(solid_fill_pattern);
         OPT_PTR(solid_infill_below_area);
         OPT_PTR(solid_infill_extruder);

src/libslic3r/PrintObject.cpp

@@ -753,6 +753,8 @@ bool PrintObject::invalidate_state_by_config_options(const std::vector<t_config_
             || opt_key == "seam_preferred_direction_jitter"
             || opt_key == "seam_travel"
             || opt_key == "small_perimeter_speed"
+            || opt_key == "small_perimeter_min_length"
+            || opt_key == "small_perimeter_max_length"
             || opt_key == "solid_infill_speed"
             || opt_key == "support_material_interface_speed"
             || opt_key == "support_material_speed"

src/libslic3r/libslic3r.h

@@ -43,7 +43,7 @@ typedef double  coordf_t;
 // When extruding a closed loop, the loop is interrupted and shortened a bit to reduce the seam.
 #define LOOP_CLIPPING_LENGTH_OVER_NOZZLE_DIAMETER 0.15
 // Maximum perimeter length for the loop to apply the small perimeter speed. 
-#define SMALL_PERIMETER_LENGTH (6.5 / SCALING_FACTOR) * 2 * PI
+//#define SMALL_PERIMETER_LENGTH (6.5 / SCALING_FACTOR) * 2 * PI
 #define INSET_OVERLAP_TOLERANCE 0.4
 //FIXME Better to use an inline function with an explicit return type.
 //inline coord_t scale_(coordf_t v) { return coord_t(floor(v / SCALING_FACTOR + 0.5f)); }

src/slic3r/GUI/ConfigManipulation.cpp

@@ -359,7 +359,7 @@ void ConfigManipulation::toggle_print_fff_options(DynamicPrintConfig* config)
         "only_one_perimeter_top", "ensure_vertical_shell_thickness", "thin_walls", 
         "overhangs", "overhangs_reverse",
         "seam_position", "external_perimeters_first", "external_perimeters_vase", "external_perimeter_extrusion_width",
-        "perimeter_speed", "small_perimeter_speed", "external_perimeter_speed", "perimeter_loop", "perimeter_loop_seam" })
+        "perimeter_speed", "small_perimeter_speed", "small_perimeter_min_length", " small_perimeter_max_length", "external_perimeter_speed", "perimeter_loop", "perimeter_loop_seam" })
         toggle_field(el, have_perimeters);
 
     toggle_field("overhangs_width", config->option<ConfigOptionFloatOrPercent>("overhangs_width_speed")->value > 0);

src/slic3r/GUI/Preset.cpp

@@ -468,7 +468,11 @@ const std::vector<std::string>& Preset::print_options()
         "max_volumetric_extrusion_rate_slope_positive", "max_volumetric_extrusion_rate_slope_negative", 
 #endif /* HAS_PRESSURE_EQUALIZER */
         "min_width_top_surface",
-        "perimeter_speed", "small_perimeter_speed", "external_perimeter_speed", "infill_speed", "solid_infill_speed", 
+        "perimeter_speed",
+        "small_perimeter_speed",
+        "small_perimeter_min_length",
+        "small_perimeter_max_length",
+        "external_perimeter_speed", "infill_speed", "solid_infill_speed", 
         "top_solid_infill_speed", "support_material_speed", "support_material_xy_spacing", "support_material_interface_speed",
         "bridge_speed",
         "gap_fill",