supermerill#4005

gcode now emmits SET_VELOCITY_LIMIT instead of m204 commands with the decleration value
"work arounds" are mentioned a fair bit in Voron discord.
"work around" is also using custom_gcode
figured i'll add it quickly.

updated tooltip for travel_deceleration_use_target and deceleration_factor
removed deceleration_match_to_er_acceleration
improvements for deceleration_factor.

seems to work well now.
updated tooltip for deceleration_factor.

This reverts commit cb1e694.

This reverts commit bfdff0d.

This reverts commit 94cb239.

initial upload, still alot of work to-do!
generates and slices model just fine.
few bugs to workout, mainly with CalibrationPressureAdvDialog.cpp model sizing and what not
per_objects_gcode i'm wanting to be a 'powerfull' tool that can be used, later it will be used to insert the smooth_time bits aswell.

need help with inserting the per_objects_gcode where it's supposed to be :upside_down: currently it only writes it all at the start of the file(helps verifying it's correct)

made new 3mf models for the new scaling method i'm using
might put them in another folder later

needed a more clear description of path when reading code, considering adding a "wave 90 bend" model, the "wave" style should make it more obvious between PA values instead of focusing on the corner.

removed other border file, easier to use 1 model for the border.

managed to fix scaling issue with different nozzle sizes.
tested with fair few combinations of nozzle sizes, layer height, base layer height, extrusion role widths.
seems solid on that part now.
added "verify" extended feature, this is just for users to see what ER roles need a new PA value

scaling of the borders can still be improved though. it's decent enough for now, but on larger nozzle sizes the borders/numbers get a touch too large and you get "overhangs"

TODO: bug test, for any values that get used if percent/float ect
TODO: find calculation for external/internal bridges, overhang, ironing, support material/interface
TODO: add more info to .html file.

fixed GUI prompt for "unsupported firmware type"

need to figure out the math required for the right border so it will be scaled with the numbers..
math is hard :(

need to re-adjust scale for left/top/bottom now, since larger nozzle sizes can prevent bottom solid layers forming.

added prefill value for 'before_layer_gcode'

updated to 2.5.59.11
adjusted scale in z for the 90_bend models so print would be slightly quicker.
found a couple new bugs with merge regarding the auto arrange
everything else seems to be ok.

allow to write some gcode each layer, when an object began to print.
Useful for calibrations.

allow to write some gcode each time a region start to print something (perimeter, infill, ironing).
Useful for calibrations.

 * fix all step invalidation incoherence
 * rename bridge_internal_* settings to internal_bridge (like orca)
 * reorder entries when they weren't sorted by alphanumeric order.

large improvements.
now possible to config multi-plate testing
changed default values for test.
cleaned code up a fair bit
found //BUG: custom gcode ' between extrusion role changes' should that be before or after region gcode?

updated to master, adjusted pressure calibration max tests to 10

large improvements.
now possible to config multi-plate testing
changed default values for test.
cleaned code up a fair bit
found //BUG: custom gcode 'between extrusion role changes' should that be before or after region gcode?

adjusted scale in z for the 90_bend models so print would be slightly quicker.
found a couple new bugs with merge regarding the auto arrange
everything else seems to be ok.

found issue with origin point on exported models.
adjusted numbers model to be 1 line width prev was x2 line width
set sizes to exact numbers

removed a bunch of lines and cleaned up.
couple new small features. loads extra number for test ID to bottom right of model.
fixed scaling in xyz
fixed flow calculations for scaling
max height of *5 layer_height
set read only for "number of tests" to create 10 is max(because of test ID feature, this can be fixed later on.)
set read only for "extrusion role" select
updated tooltips
removed some unnecessary text from main config window
on updating row count it auto populates the next rows(this is kinda buggy and could use improving)

i have not done any prints with beta v1.20 yet
up next: fix the welcome page and have it provide usefull information 😃

fixed bugs with default values not getting set.
fixed issue with 'internal_bridge_speed' missing on GUI

small typo in "before_layer_gcode" there is no layer "0"!
added 'false' flag for rotate when adding models, this might fix 45 degree printer bug?

first_layer when generating tests will no longer have gap fill.
first_layer now adds it's PA command correctly and each test has it's independent value
welcome page now autoselects last selected role when running multitest plates.
infill_every_layers for internalinfill is now supported
if your feature_gcode contains firmwares set PA/LA commands it will be auto commented out when exporting .gcode file

added darkmode support for the calibration windows (i still need to test the other calibration windows if they still work, and are clickable)
added support for the support material layerheight
i need to get the switch statement working to help with maintainability then do alot more refactoring

2.7 notes:
compiled 2.7 and made adjustments here so it's ready.
arrangement process, and object modifiers are broken, everything else seems to be ok(have not checked the gcode output)
scrolling in the object list is now very slow/the scrolling action gets a 'queue' if you scroll then stop the GUI keeps going then stops