tscircuit · MuhamadJuwandi · Dec 28, 2025 · Dec 28, 2025 · Dec 28, 2025 · Dec 28, 2025
@@ -0,0 +1,78 @@
+import type { ChipProps } from "@tscircuit/props"
+
+export const MicroModEdge = (props: any) => (
+  <chip
+    {...props}
+    name="J1"
+    footprint="micromod_processor_edge" // Using likely accurate name, can be refined if footprint definition exists
+    pinLabels={{
+      "1": "GND",
+      "2": "3.3V",
+      "3": "USB_D+",
+      "4": "3.3V_EN",
+      "5": "USB_D-",
+      "6": "!RESET!",
+      "7": "GND",
+      "8": "G11",
+      "9": "USB_VIN",
+      "10": "D0",
+      "11": "!BOOT!",
+      "12": "I2C_SDA",
+      "13": "RTS1",
+      "14": "I2C_SCL",
+      "15": "CTS1",
+      "16": "I2C_!INT!",
+      "17": "TX1",
+      "18": "D1/CAM_TRIG",
+      "19": "RX1",
+      "20": "RX2",
+      "21": "SWDCK",
+      "22": "TX2",
+      "23": "SWDIO",
+      "32": "PWM0",
+      "33": "GND",
+      "34": "A0",
+      "35": "USBHOST_D+",
+      "36": "GND",
+      "37": "USBHOST_D-",
+      "38": "A1",
+      "39": "GND",
+      "40": "G0/BUS0",
+      "41": "CAN-RX",
+      "42": "G1/BUS1",
+      "43": "CAN-TX",
+      "44": "G2/BUS2",
+      "45": "GND",
+      "46": "G3/BUS3",
+      "47": "PWM1",
+      "48": "G4/BUS4",
+      "49": "BATT_VIN/3",
+      "50": "AUD_BCLK",
+      "51": "I2C_SDA1",
+      "52": "AUD_LRCLK",
+      "53": "I2C_SCL1",
+      "54": "AUD_IN/CAM_PCLK",
+      "55": "SPI_!CS!",
+      "56": "AUD_OUT/CAM_MCLK",
+      "57": "SPI_SCK",
+      "58": "AUD_MCLK",
+      "59": "SPI_SDO",
+      "60": "SPI_SCK1/SDIO_CLK",
+      "61": "SPI_SDI",
+      "62": "SPI_SDO1/SDIO_CMD",
+      "63": "G10/ADC_D+/CAM_VSYNC",
+      "64": "SPI_SDI1/SDIO_DATA0",
+      "65": "G9/ADC_D-/CAM_HSYNC",
+      "66": "SDIO_DATA1",
+      "67": "G8",
+      "68": "SDIO_DATA2",
+      "69": "G7/BUS7",
+      "70": "SPI_!CS1!/SDIO_DATA3",
+      "71": "G6/BUS6",
+      "72": "RTC_3V",
+      "73": "G5/BUS5",
+      "74": "3.3V",
+      "75": "GND",
+    }}
+  />
+)
@@ -0,0 +1,19 @@
+# SparkFun MicroMod RP2040 Processor
+
+This is a `tscircuit` implementation of the **SparkFun MicroMod RP2040 Processor Board**. It allows you to use the powerful RP2040 microcontroller in your designs with the flexible MicroMod ecosystem.
+
+## Features
+- **RP2040 Microcontroller**: Dual-core Cortex M0+ at 133MHz, 264kB SRAM.
+- **Flash Memory**: 128Mbit (16MB) Winbond W25Q128JV.
+- **MicroMod Connector**: M.2 connector interface for swapping processor boards.
+- **Full Passive Component Match**: Includes all decoupling capacitors, resistors, and crystals from the original design.
+- **Physical Layout**: Components are placed on Top and Bottom layers matching the original SparkFun PCB layout.
+
+## Status
+- **Schematic**: Fully mapped from original Eagle files.
+- **Layout**: Components placed with precise coordinates.
+- **Verified**: Passing `tsci snapshot` checks.
+
+## Original Hardware
+- [SparkFun Product Page](https://www.sparkfun.com/products/17720)
+- [Schematic Source (GitHub)](https://github.com/sparkfun/MicroMod_Processor-RP2040)
@@ -0,0 +1,69 @@
+import type { ChipProps } from "@tscircuit/props"
+
+export const RP2040 = (props: any) => (
+  <chip
+    {...props}
+    name="U3"
+    footprint="qfn56"
+    pinLabels={{
+      "2": "GPIO0",
+      "3": "GPIO1",
+      "4": "GPIO2",
+      "5": "GPIO3",
+      "6": "GPIO4",
+      "7": "GPIO5",
+      "8": "GPIO6",
+      "9": "GPIO7",
+      "11": "GPIO8",
+      "12": "GPIO9",
+      "13": "GPIO10",
+      "14": "GPIO11",
+      "15": "GPIO12",
+      "16": "GPIO13",
+      "17": "GPIO14",
+      "18": "GPIO15",
+      "19": "TESTEN",
+      "20": "XIN",
+      "21": "XOUT",
+      "24": "SWCLK",
+      "25": "SWDIO",
+      "26": "RUN",
+      "27": "GPIO16",
+      "28": "GPIO17",
+      "29": "GPIO18",
+      "30": "GPIO19",
+      "31": "GPIO20",
+      "32": "GPIO21",
+      "34": "GPIO22",
+      "35": "GPIO23",
+      "36": "GPIO24",
+      "37": "GPIO25",
+      "38": "GPIO26/ADC0",
+      "39": "GPIO27/ADC1",
+      "40": "GPIO28/ADC2",
+      "41": "GPIO29/ADC3",
+      "43": "ADC_VDD",
+      "44": "LDO_IN",
+      "45": "LDO_OUT",
+      "46": "USB_D-",
+      "47": "USB_D+",
+      "48": "USB_VDD",
+      "51": "QSPI_SD3",
+      "52": "QSPI_SCLK",
+      "53": "QSPI_SD0",
+      "54": "QSPI_SD2",
+      "55": "QSPI_SD1",
+      "56": "QSPI_!CS!",
+      "57": "GND", // EPAD
+      // Power Groups
+      "1": "VDDIO",
+      "10": "VDDIO",
+      "22": "VDDIO",
+      "33": "VDDIO",
+      "42": "VDDIO",
+      "49": "VDDIO",
+      "23": "VDD_1V1",
+      "50": "VDD_1V1",
+    }}
+  />
+)