Skip to content

ut-amrl/Point-LIO

 
 

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

12 Commits
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Repository files navigation

Point-LIO

Point-LIO: Robust High-Bandwidth Lidar-Inertial Odometry

1. Introduction

The framework and key points of the Point-LIO.

Point-LIO is a robust and high-bandwidth LiDAR-inertial odometry with the capability to estimate extremely aggressive robotic motions. Point-LIO has two key novelties that enable a high-bandwidth LiDAR-inertial odometry (LIO). The first one is a point-by-point LIO framework, where the state is updated at each LiDAR point measurement without accumulating them into a frame. This point-by-point update allows an extremely high-frequency odometry output, significantly increases the odometry bandwidth, and also fundamentally removes the artificial in-frame motion distortion in aggressive motions. The second main novelty is a stochastic process-augmented kinematic model which models the IMU measurements as an output, instead of input as in existing filter-based odometry or SLAM systems, of the model. This new modeling method enables accurate localization and reliable mapping for aggressive motions even when IMU measurements are saturated. In experiments, Point-LIO is able to provide accurate, high-frequency odometry (4-8 kHz) and reliable mapping under severe vibrations and aggressive motions with high angular velocity (75 rad s^{-1}) beyond the IMU measuring ranges. And Point-LIO is computationally efficient, robust, versatile on public datasets with general motions. As an odometry, Point-LIO could be used in various autonomous tasks, such as trajectory planning, control, and perception, especially in cases involving very fast ego-motions (e.g., in the presence of severe vibration and high angular or linear velocity) or requiring high-rate odometry output and mapping (e.g., for high-rate feedback control and perception).

1.1. Developers:

The codes of this repo are contributed by: Dongjiao He (贺东娇) and Wei Xu (徐威)

1.2. Related paper

Our paper is accepted to Advanced Intelligent Systems(AIS), and is in the process of production. The preprint version is attached here, Point-LIO_preprint.pdf

1.3. Related video

Our accompany video is available on YouTube.

2. What can Point-LIO do?

2.1 Simultaneous LiDAR localization and mapping (SLAM) without motion distortion

2.2 Produce high odometry output frequence and high bandwidth

2.3 SLAM with aggressive motions even the IMU is saturated

3. Prerequisites

3.1 Ubuntu and ROS

We tested our code on Ubuntu18.04 with ros melodic and Ubuntu20.04 with noetic. Additional ROS package is required:

sudo apt-get install ros-xxx-pcl-conversions

3.2 Eigen

Following the official Eigen installation, or directly install Eigen by:

sudo apt-get install libeigen3-dev

3.3 livox_ros_driver

Follow livox_ros_driver Installation.

Remarks:

  • Since the Point-LIO supports Livox serials LiDAR, so the livox_ros_driver must be installed and sourced before run any Point-LIO luanch file.
  • How to source? The easiest way is add the line source $Licox_ros_driver_dir$/devel/setup.bash to the end of file ~/.bashrc, where $Licox_ros_driver_dir$ is the directory of the livox ros driver workspace (should be the ws_livox directory if you completely followed the livox official document).

4. Build

Clone the repository and catkin_make:

    cd ~/$A_ROS_DIR$/src
    git clone https://github.com/hku-mars/Point-LIO.git
    cd Point-LIO
    git submodule update --init
    cd ../..
    catkin_make
    source devel/setup.bash
  • Remember to source the livox_ros_driver before build (follow 3.3 livox_ros_driver)
  • If you want to use a custom build of PCL, add the following line to ~/.bashrc export PCL_ROOT={CUSTOM_PCL_PATH}

5. Directly run

Important notes:

A. Please make sure the IMU and LiDAR are Synchronized, that's important.

B. Please obtain the saturation values of your used IMU (i.e., accelerator and gyroscope), and the units of the accelerator of your used IMU, then modify the .yaml file according to those settings. That's improtant.

C. The warning message "Failed to find match for field 'time'." means the timestamps of each LiDAR points are missed in the rosbag file. That is important because Point-LIO processes at the sampling time of each LiDAR point.

D. We recommend to set the extrinsic_est_en to false if the extrinsic is give. As for the extrinsic initiallization, please refer to our recent work: Robust and Online LiDAR-inertial Initialization.

E. If a high odometry output frequency without downsample is required, set publish_odometry_without_downsample as true. Then the warning message of tf "TF_REPEATED_DATA" will pop up in the terminal window, because the time interval between two publish odometery is too small. The following command could be used to suppress this warning to a smaller frequency:

in your catkin_ws/src,

git clone --branch throttle-tf-repeated-data-error [email protected]:BadgerTechnologies/geometry2.git

Then rebuild, source setup.bash, run and then it should be reduced down to once every 10 seconds. If 10 seconds is still too much log output then change the ros::Duration(10.0) to 10000 seconds or whatever you like.

5.1 For Avia

Connect to your PC to Livox Avia LiDAR by following Livox-ros-driver installation, then

    cd ~/$Point_LIO_ROS_DIR$
    source devel/setup.bash
    roslaunch point_lio mapping_avia.launch
    roslaunch livox_ros_driver livox_lidar_msg.launch
  • For livox serials, Point-LIO only support the data collected by the livox_lidar_msg.launch since only its livox_ros_driver/CustomMsg data structure produces the timestamp of each LiDAR point which is very important for Point-LIO. livox_lidar.launch can not produce it right now.
  • If you want to change the frame rate, please modify the publish_freq parameter in the livox_lidar_msg.launch of Livox-ros-driver before make the livox_ros_driver pakage.

5.2 For Livox serials with external IMU

mapping_avia.launch theratically supports mid-70, mid-40 or other livox serial LiDAR, but need to setup some parameters befor run:

Edit config/avia.yaml to set the below parameters:

  1. LiDAR point cloud topic name: lid_topic
  2. IMU topic name: imu_topic
  3. Translational extrinsic: extrinsic_T
  4. Rotational extrinsic: extrinsic_R (only support rotation matrix)
  • The extrinsic parameters in Point-LIO is defined as the LiDAR's pose (position and rotation matrix) in IMU body frame (i.e. the IMU is the base frame). They can be found in the official manual.
  1. Saturation value of IMU's accelerator and gyroscope: satu_acc, satu_gyro
  2. The norm of IMU's acceleration according to unit of acceleration messages: acc_norm

5.3 For Velodyne or Ouster (Velodyne as an example)

Step A: Setup before run

Edit config/velodyne.yaml to set the below parameters:

  1. LiDAR point cloud topic name: lid_topic
  2. IMU topic name: imu_topic (both internal and external, 6-aixes or 9-axies are fine)
  3. Set the parameter timestamp_unit based on the unit of time (Velodyne) or t (Ouster) field in PoindCloud2 rostopic
  4. Line number (we tested 16, 32 and 64 line, but not tested 128 or above): scan_line
  5. Translational extrinsic: extrinsic_T
  6. Rotational extrinsic: extrinsic_R (only support rotation matrix)
  • The extrinsic parameters in Point-LIO is defined as the LiDAR's pose (position and rotation matrix) in IMU body frame (i.e. the IMU is the base frame).
  1. Saturation value of IMU's accelerator and gyroscope: satu_acc, satu_gyro
  2. The norm of IMU's acceleration according to unit of acceleration messages: acc_norm

Step B: Run below

    cd ~/$Point_LIO_ROS_DIR$
    source devel/setup.bash
    roslaunch point_lio mapping_velody16.launch

Step C: Run LiDAR's ros driver or play rosbag.

5.4 PCD file save

Set pcd_save_enable in launchfile to 1. All the scans (in global frame) will be accumulated and saved to the file Point-LIO/PCD/scans.pcd after the Point-LIO is terminated. pcl_viewer scans.pcd can visualize the point clouds.

Tips for pcl_viewer:

  • change what to visualize/color by pressing keyboard 1,2,3,4,5 when pcl_viewer is running.
    1 is all random
    2 is X values
    3 is Y values
    4 is Z values
    5 is intensity

6. Examples

6.1. Example-1: SLAM on datasets with aggressive motions where IMU is saturated

6.2. Example-2: Application on FPV and PULSAR

PULSAR is a self-rotating actuated by only one motor, PULSAR

7. Contact us

If you have any questions about this work, please feel free to contact me <hdj65822ATconnect.hku.hk> and Dr. Fu Zhang <fuzhangAThku.hk> via email.

About

No description, website, or topics provided.

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published

Languages

  • C++ 99.4%
  • CMake 0.6%