Skip to content

wortell/sentinel-lamp

Folders and files

NameName
Last commit message
Last commit date

Latest commit

 

History

7 Commits
 
 
 
 
 
 
 
 

Repository files navigation

Sentinel lamp

A 3D printable Sentinel wifi enabled smart light powered by WLED and compatible with Home Assistant

Picture of a fully constructed Sentinel lamp

Instruction video:

Instruction Video

Components

To build the Sentinel lamp, you'll need access to a 3D printer, soldering iron and the following components:

Assuming you already have the PLA filament and a spare USB lead, the construction cost for the electrical components works out at less than EUR 20 per lamp.

Instructions

The lamp itself consists of 3 printable parts, printed in regular PLA on a printer with greater than a 210mmx210mm print bed (this was tested with an Ender 3 S1 Pro)

All models are designed to be printed without supports.

The 3 components are:

When constructed they snap-fit together as shown.

Cross-section of the Sentinel lamp

When you have assembled your 3d printed parts you can begin contruction.

In case you don't want to hang the lamp to the wall, a stand can be printed. The following component needs to be printed for the stand:

The point of the stand fits in the hole that otherwise would be used to hang the lamp to the wall. With stand, the lamp looks like:

Sentinel lamp with stand - frontSentinel lamp with stand - back

Step 1 - Install WLED

First, you'll want to flash your D1 Mini device with WLED and then configure it to connect to your WiFi network. the WLED project is an open source firmware for many embedded devices that allow you to create beatiful LED displays and network them together. There are controller apps for iOS and Android and it is also fully compatible with the popular Home Assistant software meaning that once built you can control your lamp from anywhere and build any number of automations so that it flashes when someone stars your GitHub repo, changes color when your build breaks or switches on and off with your office lights.

Note that for large LED displays you can need significant power, you'll also likely want a controller that has a level shifter to send a reliable 5v signal for data to your LED strip. However as we're only powering 100 or so LED's you can get away with pulling the power and data directly from the pins of an inexpensive D1 Mini.

The quickest and easiest way to install WLED on your D1 mini is to plug it into the USB socket on your computer and then visit the WLED web installer site.

Flash the device with the latest build of WLED, configure the device to connect to your WiFi network and then you are ready to go.

Step 2 - Stick the LED Strip to the White Inner

The White Inner component acts as the guide for the flexible LED strip as well as the diffuser for the lights which are stuck to the side. You only need the +5v, G and Data pins so snip off any additional power lines that might come with your strip or solder on new wires to the strip if yours didn't come with pre-soldered wires. Remove the plastic from the adhesive backing and start sticking at the bottom middle, looping around the outside then over to the inside and finally around the central part. Cut at the marked lines when you are finally done.

Path of the LED strip

When finished you should have around 100 LED's in your lamp, but it's worth counting at this point as you'll need the exact number later.

Step 3 - Add the Reflector

Next, feed the wires through the hole in the reflector. If you are using plugs to connect your strip and controller then you can do this at any time but if you are soldering the strip directly to the controller then you need to do it now.

Step 4 - Solder LED Strip to D1 Mini

Rather than use plugs, I solder my strip directly to my D1 Mini. Solder the red power wire to the 5V hole, the white ground wire to the G hole and the green data wire to the D4 hole.

The wires from the LED strip soldered to the D1 Mini

Step 5 - Assemble

Next up, feed your USB lead through the back of the black outer body and connect it to your D1 Mini. Place the D1 Mini in the small inlaid portion in the center of the lamp. Then drop in the relfector and finally place the white inner onto it, and snap fit into the black outer body. This should force the white reflector down which then also secures the electronics in place. Power up your device and at this point about half of your LED's should be glowing orange.

Step 6 - Connect to WLED and configure display

All the rest of the configuration is configuring WLED for your device. Connect using the IP address from installation time, then go to Config, LED Preferences and update the Length of the LED strip to be the number of LED's you installed in Step 2 (for me that's typically between 99 - 105). When you press Save the rest of your LED's should be glowing orange.

You can now configure your light display with the amazing flexibility of WLED. Once you have your favorite setting, store it as a preset and then go back to the LED Preferences and scroll down to Defaults where you can set which preset it displayed when the lamp is powered on (i.e. Preset 1 instead of the default orange in Preset 0)

Step 7 - Share your makes!

That's it! You are now done but I'd love to see pictures of your built and assembled lamps. Feel free to share pictures of them in discussions here or on social media and tag us on Twitter @wortell and other socials

Credits

Big thanks to Martin Woodward for the inspiration, and the initial work on the GitHub Octocat lamp, and his GitHub repositories, that we have used as the basis for our design and approach.

About

Build your own Sentinel lamp

Resources

License

Stars

Watchers

Forks

Releases

No releases published

Packages

No packages published