Frontier Silicon Radio Binding

Documentation of the Frontier Silicon Radio binding for Internet Radios based on the Frontier Silicon chipset.

Introduction

This binding has been developed and tested with the Hama IR110 and Medion MD87180 internet radios. The MEDION® P85040 (MD 86988), MEDION® P85035 (MD 87090), MEDION® P85105 (MD 87505), Pinell Supersound II, Silvercrest SIRD 14 C1, Silvercrest SIRD 14 C2, Revo Supersystem, Revo Superconnect, Ruark R2, Technisat DigiRadio 450 and the Hama DIR3110 / Hama DIT2000M are also supported. No radio, but also supported: Silvercrest SMRS 35 A1 (WLAN box), and Silvercrest SMRB 40 A1 (WLAN Soundbar)

You can easily check if your IP radio is supported:

1. Figure out the IP of your radio (e.g. by looking it up in your router)
2. Figure out the PIN that is configured for the radio (somewhere hidden in the radio's on-screen menu); or try the default pin 1234
3. Go to your web browser and enter: http://<IP>/fsapi/CREATE_SESSION?pin=<PIN>
4. If the response is similar to FS_OK 6836164442, your radio is most likely compatible with this binding
5. If you radio works with this binding, please add it to the list above by Editing this page!

For installation of the binding, please see Wiki page Bindings.

The Frontier Silicon Radio binding is included since openHAB 1.7.0.

Binding Configuration

Configuration is done in the openhab.cfg file (in the folder ${openhab_home}/configurations):

############################### Frontier Silicon Radio Binding ###################################
#
# Hostname/IP of the radio to control
#frontiersiliconradio:radio.host=192.168.0.100

# PIN access code of the radio (default: 1234)
#frontiersiliconradio:radio.pin=1234

# Portnumber of the radio to control (optional, defaults to 80)
#frontiersiliconradio:radio.port=80

# The number of milliseconds between checks of the radio
# (optional, defaults to 60 seconds).
#frontiersiliconradio:refreshInterval=60000

# Cache the state for n minutes so only changes are posted (optional, defaults to 0 = disabled)
# Example: if period is 60, once per hour all states are posted to the event bus;
#          changes are always and immediately posted to the event bus.
# The recommended value is 60 minutes.
#frontiersiliconradio:cachePeriod=60

Some notes:

• 'radio' is an identifier that can be replaced with your custom identifier, e.g. 'bedroom' or 'radio-kitchen'. This allows to use the binding also for multiple radios.
• The pin may vary from radio to radio, you can typically look it up in the radio settings.
• 'refreshInterval' and 'cachePeriod' are global settings that apply to all radios.

Item Binding Configuration

There are different types of item bindings, all of them are qualified with the device's identifier used in the openhab.cfg file:

frontiersiliconradio="<identifier>:<property>"

Example for the power state of a device with identifier radio:

Switch RadioPower "Radio Power" { frontiersiliconradio="radio:POWER" }

A list of all properties and their possible item types is given below:

item	item type	purpose	changeable
POWER	Switch	power state	yes
MODE	Number	radio mode (details about mapping below)	yes
VOLUME	Number	volume	yes
MUTE	Swtich	mute	yes
PLAYINFONAME	String	title of current playback, e.g. radio station	no
PLAYINFOTEXT	String	additional information, e.g. current song	no
PRESET	Number	select preset, e.g. configured radio stations	yes

The radio mode property is just a number that specifies the radio mode which may differ for each radio. This is why there is no fixed mapping implemented. For radios listed above, the mapping is as follows (please add your radio mapping, if it differs!):

Please use the second, transposed table below this table, it is easier to extend and maintain This first table should become obsolete

radio mode	Hama IR110	Medion MD 87180/87090	Medion MD 86988	Pinell Supersound II	Silvercrest SIRD 14 C1	Revo Superconnect	Hama DIR3110	Hama DIT2000M	TinyAudio M7+	Silvercrest SMRS 35 A1 (WLAN box)	Silvercrest SMRB 40 A1 (WLAN Soundbar)
0	Internet Radio	Internet Radio	Internet Radio	Internet Radio	Internet Radio	Internet Radio	Internet Radio	Internet Radio	Internet Radio	Internet Radio	Internet Radio
1	Spotify	Music Player (USB, LAN)	Music Player	Spotify	Spotify	Spotify	Spotify	Spotify	-	TIDAL	TIDAL
2	Player	DAB Radio	FM Radio	Player	---	---	Player	---	Player	Napster	Napster
3	AUX in	FM Radio	AUX in	DAB Radio	Music Player	Music Player	DAB Radio	Music Player	DAB Radio	Deezer	Deezer
4	-	AUX in	-	FM Radio	DAB Radio	DAB Radio	FM Radio	DAB Radio	FM Radio	Qobuz	Qobuz
5	-	-	-	AUX in	FM Radio	FM Radio	AUX in	FM Radio	-	Spotify	Spotify
6	-	-	-	-	AUX in	AUX in	-	AUX in	-	Local Music	Local Music
7	-	-	-	-	-	Bluetooth	-	-	-	Music Player	Music Player
8	-	-	-	-	-	-	-	-	-	AUX in	Bluetooth
9	-	-	-	-	-	-	-	-	-	-	AUX in
10	-	-	-	-	-	-	-	-	-	-	Optical in

For ease of reading and extending this table, I start a transposed version of this table:

device\ radio mode	0	1	2	3	4	5	6	7	8	9	10	11
Hama IR110	Internet Radio	Spotify	Player	AUX
Hama DIR3110	Internet Radio	Spotify	Music Player	DAB	FM	AUX
Hama DIT2000M	Internet Radio	Spotify		Music Player	DAB	FM	AUX
Medion MD 87180/97090	Internet Radio	Music Player	DAB	FM	AUX
Medion MD 86988	Internet Radio	Spotify	Player	AUX
Pinell Supersound II	Internet Radio	Spotify	Music Player	DAB	FM	AUX
Silvercrest SIRD 14 C1	Internet Radio	Spotify		Music Player	DAB	FM	AUX
Silvercrest SIRD 14 C2	Internet Radio	TIDAL	Napster	Deezer	Qobuz	Spotify	Local Music	Music Player	DAB	FM	AUX	Network
Silvercrest SMRS 35 A1 (WLAN box)	Internet Radio	TIDAL	Napster	Deezer	Qobuz	Spotify	Local Music	Music Player	AUX
Silvercrest SMRB 40 A1 (WLAN soundbar)	Internet Radio	TIDAL	Napster	Deezer	Qobuz	Spotify	Local Music	Music Player	Bluetooth	AUX	Optical
Revo Superconnect	Internet Radio	Spotify		Music Player	DAB	FM	AUX	Bluetooth
TinyAudio M7+	Internet Radio		Music Player	DAB	FM

If your radio is not listed, try http://<IP>/fsapi/LIST_GET_NEXT/netRemote.sys.caps.validModes/-1?pin=1234&maxItems=65536

Example

Items:

Switch RadioPower         "Radio Power" (gRadio) { frontiersiliconradio="radio:POWER" }
Number RadioMode          "Radio Mode [%d]" (gRadio) { frontiersiliconradio="radio:MODE" }
Switch RadioMute          "Radio Mute" (gRadio) { frontiersiliconradio="radio:MUTE" } 
Number RadioVolDimmer     "Radio Volume [%d %%]" (gRadio) { frontiersiliconradio="radio:VOLUME" } 
String RadioPlayInfoName  "Play Info Name [%s]" (gRadio) { frontiersiliconradio="radio:PLAYINFONAME" }
String RadioPlayInfoText  "Play Info Text [%s]" (gRadio) { frontiersiliconradio="radio:PLAYINFOTEXT" }
Number RadioPreset        "Preset" (gRadio) { frontiersiliconradio="radio:PRESET" }

Sitemap (presets and mode are radio-specific, this is why their mapping is specified here):

Frame label="Radio Control" {
    Switch     item=RadioPower
    Selection  visibility=[RadioPower==ON] item=RadioPreset mappings=[0="1Live", 1="WDR2", 2="SWR3"]
    Selection  visibility=[RadioPower==ON] item=RadioMode   mappings=[0="Internet Radio", 1="Spotify", 2="Player", 3="AUX IN"]
    Slider     visibility=[RadioPower==ON] item=RadioVolDimmer
    Switch     visibility=[RadioPower==ON] item=RadioMute
    Text       visibility=[RadioPower==ON] item=RadioPlayInfoName
    Text       visibility=[RadioPower==ON] item=RadioPlayInfoText
}

Developer Info

If you would like to extend this binding and contribute further functionality, here is some technical information about it. The communication with the radio is realized via simple HTTP requests. Unfortunately, there is no official documentation of the API for the frontier silicon chipset, but there are some sources around the internet (flammy/fsapi on github, for example). Until now, only the following requests are implemented:

• netRemote.sys.power
• netRemote.sys.mode
• netRemote.sys.audio.volume
• netRemote.sys.audio.mute
• netRemote.nav.action.selectPreset
• netRemote.play.info.text
• netRemote.play.info.name

If you like to add further actions, have a look at FrontierSiliconRadio.java.