MAX! CUL Binding

Documentation of the MAX!CUL Binding. Targeting 1.6.0 release

Introduction

The aim of this binding is to allow the connection OpenHAB to MAX! devices (wall thermostat/radiator valves) using the CUL USB dongle rather than the MAX! Cube. This should allow greater control over the devices than the cube offers as all interaction is handled manually.

A lot of credit must go to the FHEM project- without their implementation of the MAX interface with CUL this would be taking a lot longer to implement!

Status

The binding is currently under heavy development and it is recommended that you currently do not rely on it. This page will be updated as things progress.

Features

The binding currently offers the following features:

• Listen mode - this allows you to listen in on MAX! network activity from a MAX!Cube for example. A trace will be output in debug mode that decodes implemented messages
• Pairing - can pair devices with OpenHAB by triggering Pair Mode using a Switch item
• Wall Thermostat
• Can send set point temperature
• Can receive set point temperature
• Can receive measured temperature
• Can receive battery status
• Can receive operating mode
• Radiator Thermostat Valve
• Can send set point temperature
• Can receive set point temperature
• Can receive measured temperature
• Can receive valve position
• Can receive battery status
• Can receive operating mode
• Push Button
• Can receive either AUTO or ECO depending on button press (translated to ON/OFF)

Limitations

Aside from understanding what the binding does do which is documented here there are some key things to be aware of that may limit what you hope to achieve.

1. Radiator valve data is updated quite sporadically. Items such as set point temperature, measured temperature, valve position, battery status and operating mode are only sent when the state of the valve changes - i.e. valve moves or the dial used to manually set a temperature. If you want measured temperature it is much better to use a wall thermostat.
2. The binding has no concept of 'auto' mode. It currently has no ability to retrieve from any source and subsequently send a schedule to devices. This may change in the future, which would allow basic operation should OpenHAB fail for some reason.

Binding Configuration

Example configuration:

################################ Max!CUL Binding  ###########################################

# set the device of the CUL device
maxcul:device=serial:/dev/ttyACM1
# set the refresh interval
maxcul:refreshInterval=60000
# set timezone you want the units to be set to - default is Europe/London
maxcul:timezone=Europe/London

Item Configuration

The following devices have the following valid types:

• RadiatorThermostat - thermostat,temperature,battery,valvepos
• WallThermostat - thermostat,temperature,battery
• PushButton - switch

Examples:

• Number RadTherm1 { maxcul="RadiatorThermostat:JEQ1234565" } - will return/set the thermostat temperature of radiator thermostat with the serial number JEQ0304492
• Number RadThermBatt { maxcul="RadiatorThermostat:JEQ1234565:battery" }- will return the battery level of JEQ0304492
• Number wallThermTemp { maxcul="WallThermostat:JEQ1234566:temperature" } - will return the temperature of a wall mounted thermostat with serial number JEQ0304447
• Number wallThermSet { maxcul="WallThermostat:JEQ1234566:thermostat" } - will set/return the desired temperature of a wall mounted thermostat with serial number JEQ0304447
• Switch pushBtn { maxcul="PushButton:JEQ1234567" } - ON maps to Auto, OFF maps to Eco
• Switch pair { maxcul="PairMode" } - Switch only, ON enables pair mode for 60s. Will automatically switch off after this time.
• Switch listen { maxcul="ListenMode" } - Switch only, puts binding into mode where it doesn't process messages - just listens to traffic, parses and outputs it.

There is the option of the addition of configTemp=20.0/15.0/30.5/4.5/4.5/0.0/0.0 at the end of a thermostat device binding (wall or radiator) will allow the setting of comfort/eco/max/min/windowOpenDetectTemp/windowOpenDetectTime/measurementOffset respectively. These correspond to the following:

• comfort - the defined 'comfort' temperature (default 21.0)
• eco - the defined eco setback temperature (default 17.0)
• max - maximum temperature that can be set on the thermostat (default 30.5)
• min - minimum temperature that can be set on the thermostat (default 4.5)
• windowOpenDetectTemp - temperature threshold at which point the thermostat will assume a window is open and shut down the heating output (default is 4.5 which disables the feature)
• windowOpenDetectTime - number of minutes below threshold until 'window mode' is activated. Rounded down to the nearest 5 minutes. (default is 0)
• measurement offset - offset applied to measure temperature (range is -3.5 to +3.5) - default is 0.0

Example:

Number wallThermDesired { maxcul="WallThermostat:KEQ0946847:thermostat:configTemp=20.0/15.0/30.5/4.5/4.5/0.0/0.0" }

Technical Information

Implemented Messages

The table below shows what messages are implemented and to what extent. Transmit means we can build and transmit a packet of that type with relevant data. Decode means we can extract data into some meaningful form. All message types can be received, identified and the raw payloads displayed. Messages not identified in this table cannot be transmitted by the binding and can only be decoded as a raw payload.

Message	Transmit	Decode	Comments
ACK	Y	Y
PAIR PING	N	Y
PAIR PONG	Y	Y
SET GROUP ID	Y	Y
SET TEMPERATURE	Y	Y	Allows setting of temperature of (wall)therm
TIME INFO	Y	Y
WAKEUP	Y	N
WALL THERMOSTAT CONTROL	N	Y	Provides measured temp and set point
THERMOSTAT STATE	N	Y	Provides battery/valvepos/temperature/thermostat set point
WALL THERMOSTAT STATE	N	Y	Provides battery/valvepos/temperature/thermostat set point
PUSH BUTTON STATE	N	Y	Auto maps to ON, Eco maps to OFF

Message Sequences

For situations such as the pairing where a whole sequences of messages is required the binding has implemented a message sequencing system. This allows the implementation of a state machine for the system to pass through as messages are passed back and forth.

This will be documented in more detail in due course.

Planned Future Features

These are in no particular priority and are simply ideas. They may not get implemented at all.

1. Implement association of devices with each other so that they won't need rules to keep the Wall Thermostat and the Radiator Thermostat in sync
2. Add the ability to configure night/comfort/etc temperatures DONE
3. Add the ability to interface with the Eco switch DONE
4. Add the ability to interface with the window contact devices
5. Add the ability pretend to be a wall thermostat. This would allow us to associate with a radiator thermostat and send measured temperatures to it. These could be then sent from another binding for example.