Bill of Materials (Atom Board)
This is a bill of materials for the Atom Video to HDMI Adapter.
Latest schematics are here:
Note the 6 bit board combined with the analog board will also work with the Atom but DIY construction of this board might be easier at it is mostly through-hole.
All resistors are standard metal film (0.3W or 0.6W) 1%
| Part Description | Supplier | Quantity | Part Ref | Notes |
|---|---|---|---|---|
| 100R |
13-MFR-25FRF52-100RCT-ND MFR-25FRF52-100R RES 100 OHM 1% 1/4W AXIAL |
1 | R1 | |
| 330R |
13-MFR-25FRF52-330RCT-ND MFR-25FRF52-330R RES 330 OHM 1% 1/4W AXIAL |
2 | R23-24 | |
| 430R |
13-MFR-25FRF52-430RCT-ND MFR-25FRF52-430R RES 430 OHM 1% 1/4W AXIAL |
1 | R7 | |
| 470R |
13-MFR-25FRF52-470RCT-ND MFR-25FRF52-470R RES 470 OHM 1% 1/4W AXIAL |
10 | R8-9,R12-19 | |
| 1K0 |
13-MFR-25FRF52-1KCT-ND MFR-25FRF52-1K RES 1K OHM 1% 1/4W AXIAL |
1 | R6 | |
| 1K1 |
13-MFR-25FRF52-1K1CT-ND MFR-25FRF52-1K1 RES 1.1K OHM 1% 1/4W AXIAL |
2 | R2,4 | |
| 5K6 |
13-MFR-25FRF52-5K6CT-ND MFR-25FRF52-5K6 RES 5.6K OHM 1% 1/4W AXIAL |
1 | R10 | |
| 7K5 |
13-MFR-25FRF52-7K5CT-ND MFR-25FRF52-7K5 RES 7.5K OHM 1% 1/4W AXIAL |
2 | R3,5 | |
| 10K |
13-MFR-25FRF52-10KCT-ND MFR-25FRF52-10K RES 10K OHM 1% 1/4W AXIAL |
3 | R20-22 | |
| 12K |
13-MFR-25FRF52-12KCT-ND MFR-25FRF52-12K RES 12K OHM 1% 1/4W AXIAL |
1 | R11 | |
| 1K Preset |
3386P-102LF-ND 3386P-1-102LF TRIMMER 1K OHM 0.5W PC PIN TOP |
2 | RV1-2 | check footprint matches Bourns 3386P if substituting |
| Part Description | Supplier | Quantity | Part Ref | Notes |
|---|---|---|---|---|
| 27pF ceramic | 2 | C2-3 | not normally fitted | |
| 47nF multilayer ceramic | 2 | C5-6 | 5mm pin spacing | |
| 100nF multilayer ceramic | 4 | C1,7-8,18 | 5mm pin spacing | |
| 100nF multilayer axial ceramic |
BC5250CT-ND A104M15X7RF5TAA CAP CER 0.1UF 50V X7R AXIAL |
3 | C10-12 | min order 10 |
| 100nF 0805 multilayer ceramic | Farnell 1907331 | 3 | C9,14-15 | min order 5 |
| 10uF >16V electrolytic | Farnell 2917914 | 4 | C4,13,16-17 | min order 5 |
Note: C2-3 (on the schematic) do not normally need to be fitted. They are marked as NF on the PCB.
| Part Description | Supplier | Quantity | Part Ref | Notes |
|---|---|---|---|---|
| SN74LVC1G66DBV |
296-13253-1-ND SN74LVC1G66DBVR IC SWITCH SPST-NOX1 10OHM SOT23 |
1 | U1 | min order 10 needs to be SOT-23 package |
| LM319N | RS 533-5749 | 3 | U2-4 | TI or ST preferred |
| XC9572XL-10VQG44C |
122-1448-ND XC9572XL-10VQG44C IC CPLD 72MC 10NS 44VQFP |
1 | U5 | |
| LE33CZ |
497-4258-1-ND LE33CZ-TR IC REG LINEAR 3.3V 100MA TO92-3 |
1 | U6 | |
| 3mm Green LED |
516-HLMP-Y802-F0000-ND HLMP-Y802-F0000 LED GREEN CLEAR T-1 T/H |
2 | D1-2 |
| Part Description | Supplier | Quantity | Part Ref | Notes |
|---|---|---|---|---|
| 14 pin IC socket | CPC SC06494 | 3 | ||
| 2x5 pin male box header | CPC CN17031 | 1 | J1 | |
| 1x2 pin straight female 0.1" header | Farnell 1668331 | 1 | J2 | min order 10 |
| 1x6 pin straight male 0.1" header | Farnell 1593415 | 1 | J3 | min order 50 |
| 1x3 pin right angled male 0.1" header | Farnell 2356177 | 1 | J4 | min order 10 |
| 2x20 pin straight female 0.1" header | Farnell 2827916 | 1 | J5 | |
Note: J6-10 (on the schematic) do not need to be fitted. They are marked as NF on the PCB.
| Part Description | Supplier | Quantity | Part Ref | Notes |
|---|---|---|---|---|
| 10 way cable mounting IDC socket with strain relief | Farnell 2215247 | 2 | ||
| 10 way IDC cable | Farnell 2628362 | 1m | 20cm max length recommended |
| Part Description | Supplier | Quantity | Part Ref | Notes |
|---|---|---|---|---|
| 6mm tactile switch |
EG1833-ND TL1105BF160Q SWITCH TACTILE SPST-NO 0.05A 12V |
3 | SW1-3 | 9.5mm button length* |
| 6mm tactile switch (right angle) |
141-TL1105XF160QBLKSTEM-ND TL1105XF160QBLKSTEM SWITCH TACTILE SPST-NO 0.05A 12V |
1 | SW4 | 5.85mm button length* |
| Evatron EVA73G Enclosure | Rapid Electronics | 1 | ||
| No. 2 x 6.5mm self tapping screws | eBay | 5 |
Notes: (1) Button length is measured from switch base, see data sheet.